Belkin P73446-B Page, Refer Servicing to, qualified service, personnel or contact

HARDWARE:

BAUD RATE - - - - - - - - - 2400 bps DATA LENGTH - - - - - - - - - - 8 bits STOP BIT - - - - - - - - - - - - - - 1 bit PARITY - - - - - - - - - - - - - - NONE

P73446-B • Page 2

UPS Uninterruptible Power Supply User Manual

USB Interface Port

1.	Firmware	Version of Firmware
2.	Rating VA	Rated Power Capacity of UPS
3.	Rating Voltage	Rated Power Voltage of UPS
4.	Rating Frequency	Connected Frequency Rating of UPS
5.	Rating Battery	Rated Battery Voltage Used by UPS
6.	Input Frequency	AC Utility Frequency
7.	Input Voltage	AC Utility Voltage
8.	Output Source	Indicating Bypass or On Battery
9.	Alarm	To Set Situation for Alarm
10. Voltage Sensitivity		To Improve Transfer Time and Avoid
		Effect of I/P Distortion
11. Outlet Relay ON/OFF		Set Delay Time to Control Outlet Relay
		On/Off
12. Next Shutdown		Time to Next Scheduled Shutdown
13. Next Restart		Time to Next Restart
14. AC Source		Input Power Source of UPS
15. Battery		Condition of Battery
16. Loading		Load Percentage of UPS
17. Battery Level		Indicates the Remaining Power
		Percentage of Battery
18. Selectable Transfer Voltage		Change Transfer Voltage
19. Diagram		Input & Output Power Flow of UPS
20. Picture		General Outlook of UPS

RS232 Interface Port

RS232 Pin definition:
NC - - - - - - - - - - - - - - -	1	6 - - - - - - - - - - - - - - - -	NC
TXD - - - - - - - - - - - - - -	2	7 - - - - - - - - - - - - - - - -	NC
RXD - - - - - - - - - - - - -	3	8 - - - - - - - - - - - - - - - -	NC
NC - - - - - - - - - - - - - - -	4	9 - - - - - - - - - - - - - - - -	NC
Signal Ground - - - - - - -	5

*pin2: PC receives line RS232 data from UPS.

*pin3: PC transmits line RS232 data to UPS.

*pin5: signal ground.

*other: not used.

The RS232 communication port provides the following features:

1. Monitoring charger status

2. Monitoring battery status and condition

3. Monitoring inverter status

4.Monitoring UPS status

5.Monitoring the utility status

6.Providing the power switch function for the computer to turn on/off the utility on schedule. To save power, UPS data will be provided at 2400 baud rate and is made up of 8-bit, 1-stop-bit, and no parity-bit. All the information is provided in ASCII format.

CABLING:
	COMPUTER		UPS
RX	(pin2)	TX	(pin2)
TX	(pin3)	RX	(pin3)
GND	(pin5)	GND	(pin5)

Battery Replacement

The average life of a battery is 3-5 years before ever needing to be replaced.

EcoPower Battery Replacement Program™

In the event that the UPS needs a battery replacement, Belkin offers its EcoPower Battery Replacement Program™. This program offers a battery replacement and full service check on your UPS to ensure it is working properly to protect your connected devices. It also ensures that the battery in the UPS is discarded properly in an effort to keep our environment clean. All participants in the program will receive a two-year extended product warranty. Please call Belkin Components for detailed information regarding the cost of the program and shipping procedures.

Battery Replacement

Battery replacement is a safe procedure. You may leave the UPS On and equipment connected during this procedure. Do not replace the battery when the UPS is “On Battery”. See page 15 for diagram illustrations.

1.Set the UPS at the edge of a table (Diagram A).

2.Slide the battery compartment cover down (Diagram B).

3.Grasp the tab attached to the battery and slide the battery partially out. Then grab the battery firmly and remove; the battery wires will disconnect as the battery is pulled out (Diagram C).

4.Carefully insert the new battery halfway into the UPS. Avoid pinching the wires (Diagram D).

5.Connect the wires to the new battery according to the following configuration:

Red wire to red terminal Black wire to black terminal

6.Carefully insert the battery terminals.

7.Slide the battery compartment cover back into place (Diagram E).

The old battery must be recycled. Deliver the battery to an appropriate recycling facility or return it to Belkin in the packing carton that came with your new battery. Additional recycling information is provided with your new battery.

Battery Replacement (continued)

Refer Servicing to	Diagram A
qualified service
personnel or contact
Belkin Components.

Diagram B	Diagram C
Slide the battery	Slide the battery
compartment cover.	partially out.

Diagram D	Diagram E
Slide the battery back in.	Slide the battery
Avoid pinching	cover into place.
the wires.

Troubleshooting

PROBLEM	POSSIBLE CAUSE	SOLUTION
UPS not on	On/off/test/button not pushed or	Press the on/off/test button
LED not lit	pushed less than 3 seconds	more than 3 seconds
	Battery voltage less than 10V	Recharge the UPS at least
		4 hours
	UPS fault	Contact service personnel
UPS always at	Power cord loose	Replug the power cord
battery mode
	AC breaker is burned out	Replace the breaker
	Line voltage too high, too low,	Normal condition
	or black out
Back-up time too short	Battery not fully charged	Recharge the UPS at least
		4 hours
	UPS is overloaded	Remove some unnecessary
	loads
	Charger fault or	Replace battery
	other reason
The UPS continuously	Overload	Remove the non-critical loads
beeps
Red LED lit	Battery failure	Replace battery

Storage

11.0Storage Conditions

Store the UPS covered and upright in a cool, dry location, with its battery fully charged. Before storing, charge the UPS for at least 4 hours. Disconnect any cables connected to the computer interface port to avoid unnecessary drainage of the battery.

11.1Extended Storage

During extended storage in environments where the ambient temperature is -15°C to +30°C, charge the UPS battery every 6 months.

During extended storage in environments where the ambient temperature is +30°C to +45°C, charge the UPS battery every 3 months.

Specifications (USB Series)

CE Declaration of Conformity

We, Belkin Components, declare under our sole responsibility that the F6C325u- 220V, F6C425u-220V, F6C525u-220V, F6C625u-220V, to which this declaration relates, is in conformity with Generic Emissions Standard EN50081-1 and with Generic Immunity Standard EN50082-1 1992 to which this declaration relates, is in conformity with Generic Emissions Standard EN50081-1 and with Generic Immunity Standard EN50082-1 1992.

Belkin Components Two-Year Product Warranty

Belkin Components warrants this product against defects in materials and workmanship for two years. If a defect is discovered, Belkin will, at its option, repair or replace the product at no charge, provided it is returned during the warranty period, with transportation charges prepaid, to the authorized Belkin dealer from whom you purchased the product. Proof of purchase may be required.

This warranty does not apply if the product has been damaged by accident, abuse, misuse, or misapplication; if the product has been modified without the written permission of Belkin; or if any Belkin serial number has been removed or defaced.

THE WARRANTY AND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE IN LIEU OF ALL OTHERS, WHETHER

ORAL OR WRITTEN, EXPRESSED OR IMPLIED. BELKIN SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

No Belkin dealer, agent, or employee is authorized to make any modification, extension, or addition to this warranty.

BELKIN IS NOT RESPONSIBLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DOWNTIME, GOODWILL, DAMAGE TO OR REPROGRAMMING, OR REPRODUCING ANY PROGRAM OR DATA STORED IN OR USED WITH BELKIN PRODUCTS.

Specifications

RS232 Series

MODEL		325VA	425VA	525VA	625VA
INPUT	Capacity	325VA(211W)	425VA(255W)	525VA(315W)	625VA(375W)
	Voltage	187 Vac - 280 Vac
	Frequency	50Hz or 60Hz ±3Hz (auto sensing)
OUTPUT	Voltage	Simulated sine wave, 230Vac±8%
	(on battery)
	Frequency	50Hz or 60Hz ±1Hz
	(on battery)
	Voltage	Smart boost increases 14.8% of voltage if input is 213 to 187 Vac.
	Regulation
	AVR	Smart trim reduces 12.8% of voltage if input is 247 to 280 Vac
	Transfer Time	< 4 milliseconds, including detection time
PROTECTION	Spike Protection	150 Joules
AND FILTERING	Overload Protection	UPS automatic shutdown if overload exceeds 130% in AC mode and
		100% in back-up mode. UPS alarms continuously in > 107% or
		<130% in AC mode.
	Unit Input	Breaker for overload and short circuit protection
	Modem/Network	Single Line (2-Wire, RJ11) Network (UTP, RJ45) compatible jacks, one
		input/two output except F6C325 (Series)
	Short Circuit	UPS output cut off immediately or input breaker protection
BATTERY	Type	Sealed, maintenance-free lead acid
	Typical	4 hours (to 90% of full capacity)
	Recharge Time
	Protection	Automatic self-test and discharge protection, replace
		battery indicator
	Back-up Time	Depending on computer load...
	Full/half load	5-17 min	5-24 min.	5-32 min	5-41 min.
PHYSICAL	Net Weight	5.5kg/12.3lbs.	6kg/13.23lbs	6.5kg/14.33lbs.
	Dimension	11.4"x9.6"x12.8"
	(mm) WDH
	Input inlet	10A/250V*1pcs, EN60320
	Output outlet (UPS)	10A/250V*4pcs; EN60320/F
	Output outlet (Bypass)	10A/250V*4pcs; EN60320/F
ALARM	Battery Back-Up	Slow beeping sound (about 15 sec. interval)
	Battery Low	Rapid beeping sound (about 1 sec. interval)
	Overload	Continuous beeping sound (about 1 sec. interval)
	Fault	10 sec. beeping sound continuously
	Battery test	Slow beeping sound (about 15 sec. interval)
INTERFACE	RS232 Interface	RS232 Port (except F6C325-Series)
CONFORMANCE	Safety	CE, TUV, BSI, NF
	Surge	Meet IEEE C62.41. Category A standard
ENVIRONMENT	Ambient operation	0~95%, humidity non-condensing, 0~40°C
	Audible noise	<40dBA (1 meter from surface)
	Storage condition	-15°C – 40°C (with battery)
		-15°C – 70°C (without battery)

USB Series

MODEL		350VA			500VA		650VA
INPUT	Capacity	350VA(277W)		500VA(300W)			650VA(390W)
	Voltage	187 Vac - 280 Vac
	Frequency	50Hz or 60Hz ±3Hz (auto sensing)
OUTPUT	Voltage	Simulated sine wave, 230 Vac±8%
	(on battery)
	Frequency	50Hz or 60Hz ±1Hz
	(on battery)
	Voltage	Smart boost increases 14.8% of voltage if input is 213 to 187 Vac.
	Regulation
	AVR	Smart trim reduces 12.8% of voltage if input is 247 to 288 Vac
	Transfer Time	< 4 milliseconds, including detection time
PROTECTION	Spike Protection	150 Joules
AND FILTERING	Overload Protection	UPS automatic shutdown if overload exceeds 130% in AC mode and
		100% in back-up mode. UPS alarms continuously in > 107% or
		<130% in AC mode.
	Unit Input	Breaker for overload and short circuit protection
	Modem/Network	Single Line (2-Wire, RJ11) Network (UTP, RJ45) compatible jacks, one
		input/two output
	Short Circuit	UPS output cut off immediately or input breaker protection
BATTERY	Type	Sealed, maintenance-free lead acid
	Typical	4 hours (to 90% of full capacity)
	Recharge Time
	Protection	Automatic self-test and discharge protection, replace
		battery indicator
	Back-up Time	Depending on computer load...
	Full/half load	5-20 min	5-30 min.			5-45 min
PHYSICAL	Net Weight	5.5kg/12.3lbs.	6kg/13.23lbs			6.5kg/14.33lbs.
	Dimension	11.4"x9.6"x12.8"
	(mm) WDH
	Input inlet	10A/250V*1pc, EN60320
	Output outlet (UPS)	10A/250V*4pcs; ENG60320/F
	Output outlet (Bypass)	10A/250V*4pcs; ENG60320/F
ALARM	Battery Back-Up	Slow beeping sound (about 15 sec. interval)
	Battery Low	Rapid beeping sound (about 1 sec. interval)
	Overload	Continuous beeping sound (about 1 sec. interval)
	Fault	10 sec. beeping sound continuously
	Battery test	Slow beeping sound (about 15 sec. interval)
INTERFACE	USB Interface	USB Port
CONFORMANCE	Safety	CE, TUV, BSI, NF
	Surge	Meet IEEE C62.41. Category A standard
ENVIRONMENT	Ambient operation	0~95%, humidity non-condensing, 0~40°C
	Audible noise	<40dBA (1 meter from surface)
	Storage condition	-15°C – 40°C (with battery)
		-15°C – 70°C (without battery)