Manuals / BenQ / Computer Equipment / Projector Accessories

BenQ MX716, MX717 Tighten the screws that secures the lamp cover, Resetting the lamp timer

Models: MX717 MX716

1 66

Download 66 pages 63.46 Kb

Page 56

15.Tighten the screw(s) that secures the lamp cover.

• Loose screw may cause a bad connection, which could result in malfunction.

• Do not over tighten the screw.

MX716

MX717

16.Connect the power and restart the projector.

Do not turn the power on with the lamp cover removed.

Resetting the lamp timer

17.After the startup logo, open the On-Screen Display (OSD) menu. Go to the SYSTEM SETUP: Advanced > Lamp Settings menu. Press ENTER. The Lamp Settings page displays. Highlight Reset Lamp Timer. A warning message is displayed asking if you want to reset the lamp timer. Highlight Reset and press ENTER. The lamp time will be reset to “0”.

Do not reset if the lamp is not new or replaced as this could cause damage.

56 Maintenance

Image 56

BenQ MX716, MX717 user manual Tighten the screws that secures the lamp cover, Resetting the lamp timer

Contents

Welcome Table of contents Important safety instructions Safety InstructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Projector features IntroductionShipping contents Rear/lower side Projector exterior viewFront/upper side Controls and functions Remote control Network Setting Not available TestSource selection buttons COMPUTER-1, COMPUTER-2 Network Not availableVolume + Operating the Laser pointerMute MIC/VOL +/- Not availableRemote control effective range Replacing the remote control batteries Positioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeConnection ConnectionConnecting video source devices Connecting audioTerminal name Terminal appearance BestOperation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarity Correcting keystoneUsing the menus HighlightUsing a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press EnterIf you forget the password Entering the password recall procedurePress ENTER. The message Input Current Password appears Changing the passwordDisabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Using Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerSelection Description To cancel the timer, perform the following steps Remote paging operationsFreezing the image Hiding the imageTo activate the High Altitude Mode Using the remote controlUsing the OSD menu Operating in a high altitude environmentAdjusting the sound Adjusting the sound levelTurning off the Power On/Off Ring Tone Muting the soundControlling the projector through a LAN environment Cable connectionIf you are in a Dhcp environment If you are in a non-DHCP environmentControlling the projector remotely through a web browser Iiii Iiiv Direct power off Shutting down the projectorMain menu Sub-menu Options Menu operationMenu system System Setup Basic Time Sec Menu Settings Menu PositionRight/Bottom-Left Hr/12 hrAdvanced Description of each menu Picture Mode TemperatureSave Settings Display menu Picture menu FunctionTimer SettingsSearch Color SpaceSystem Setup Basic men Function Description OperationPanel Key LockSystem Setup Advanced menu Function Description High AltitudeAudio LampSystem Setup Advanced menu Function Description Reset AllStandby NetworkInformation menu Function Description CurrentSystem StatusMaintenance Care of the projectorSetting Lamp Mode as Economic Lamp informationGetting to know the lamp hour Extending lamp lifeTiming of replacing the lamp Status MessageReplacing the lamp MX716Use the handle to slowly pull the lamp out As shown in the figure, lower the new lamp Resetting the lamp timer Tighten the screws that secures the lamp coverIndicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installation Ceiling Mount screw M4 Max L = 8 mmKHz Timing chartSupported timing for PC input Resolution Mode Frequency KHz MHz Supported timing for Hdmi Hdcp inputSupported timing for Component-YPbPrinput TimingHorizontal Frequency Hz Frequency kHzSupported timing for Video and S-Video inputs Warranty and Copyright information Limited warrantyCopyright Disclaimer