Manuals / BenQ / Computer Equipment / Projector

BenQ MW721, MX720 manual Main menu Sub-menu Options System Setup Advanced

Models: MW721 MX720

1 61

Download 61 pages 54.58 Kb

Page 39

Main menu Sub-menu

Options

5. SYSTEM SETUP: Advanced

	High Altitude Mode		On/Off
		Mute	On/Off
		Volume
	Audio Settings	Microphone Volume
		Power On/Off	On/Off
		Ring Tone	On/Off
		Ring Tone
		Lamp Mode	Normal/Economic/SmartEco
	Lamp Settings	Reset Lamp Timer
		Equivalent Lamp Hour
	Security	Change Password
	Security	Change Security	Power On Lock
	Settings	Change Security	Power On Lock
	Settings	Settings	Web Control Lock
		Settings	Web Control Lock
	Baud Rate		2400/4800/9600/14400/19200/
	Baud Rate		38400/57600/115200
			38400/57600/115200
	Test Pattern		On/Off
		Closed Caption	On/Off
	Closed Caption	Enable	On/Off
	Closed Caption	Enable
		Caption Version	CC1/CC2/CC3/CC4
		Network	On/Off
	Standby	Microphone	On/Off
	Standby	Monitor Out	On/Off
	Settings	Monitor Out	On/Off
	Settings	Audio Pass	Off/Audio in 1/Audio in 2/Audio
		Audio Pass	Off/Audio in 1/Audio in 2/Audio
		Through	L/R/HDMI
			Status
			DHCP
			IP Address
		Wired LAN	Subnet Mask
			Default Gateway
	Network		DNS Server
	Settings
	Settings		Apply
		Projection Log In	On/Off
		Code

	AMX Device	On/Off
	Discovery	On/Off
	Discovery
	MAC Address
Reset All Settings

			•	Source
			•	Picture Mode
	6.		•	Lamp Mode
	INFORMA	Current System Status	•	Resolution
	INFORMA	Current System Status	•	3D Format
	TION		•	3D Format
	TION		•	Color System
			•	Equivalent Lamp
			•	Firmware Version

Operation 39

Image 39

BenQ MW721, MX720 manual Main menu Sub-menu Options System Setup Advanced

Contents

MX720/MW721 Digital Projector Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewProjector Controls and functionsRemote control Replacing the remote control batteries Remote control effective rangeFront Ceiling Positioning your projectorChoosing a location Front TableMX720 Obtaining a preferred projected image sizeMW721 Connection ConnectionConnecting video source devices Connecting audioPlaying sound through the projector Audio output port About the microphone inputStarting up the projector OperationFine-tuning the image clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Below is the overview of the OSD menu Using the menusIf you forget the password Using a security cable lockUtilizing the password function Setting a passwordEntering the password recall procedure Changing the passwordDisabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsMX720 MW721 About the aspect ratioGo to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes Adjusting Brilliant ColorSelecting a Color Temperature 3D Color Management Setting a preferred color temperatureSetting the presentation timer Resetting current or all picture modesSelection Description Top-Left Bottom-Left Top-Right Bottom-Right To cancel the timer, perform the following stepsRemote paging operations Freezing the imageOperating in a high altitude environment To activate the High Altitude ModeHiding the image Locking control keysAdjusting the sound Using the test patternTurning off the Power On/Off Ring Tone To select Blackboard or Whiteboard Using the teaching templatesShutting down the projector Direct power offMenu operation Menu systemMain menu Sub-menu Options Basic Main menu Sub-menu Options System Setup Advanced Operation Description of each menu Fine Tuning 3D Color Picture menu Function Description Picture ModeTemperature Color TemperatureSearch TimerInstallation SettingsReceiver System Setup Basic menu Function DescriptionOperation RemoteLamp System Setup Advanced menu Function Description HighAltitude AudioNetwork System Setup Advanced menu Function DescriptionReset All StandbyCurrent SystemStatus Care of the projector MaintenanceLamp information Getting to know the lamp hourExtending lamp life Status Message Timing of replacing the lampReplacing the lamp Connect the power and restart the projector Resetting the lamp timer Thermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsTiming chart Supported timing for PC inputKHz Supported timing for Hdmi Hdcp input Supported timing for Component-YP bP r input Supported timing for Video and S-Video inputsTiming Disclaimer Warranty and Copyright informationLimited warranty Copyright