Bertazzoni PM6V), PM6V B, PM6040X Room ventilation Location and venting, Regulation of burners

MAINTENANCE OF THE MACHINE

CHANGING THE PARTS

Before carrying out any maintenance work, disconnect the appliance from the gas and electric supply.

To replace different components such as burners, taps and electrical parts you must take out the hob from the kitchen unit by releasing the fixing hooks, unscrew the fixing screws of the burners on the work top, unscrew the fixing nuts of the electric plates which are visible on the lower part of the hob and remove the worktop in order to carry out the replacement of the defective parts.

NOTE: If the taps need replacing you also need to unscrew the two fixing screws of the gas ramp at the bottom of the hob which are found on the upper part of the latter.

For appliances equipped with automatic “ON” switches you must dismantle the “ON” switch chain before replacing the taps.

You are advised to change the seal on the tap every time you replace a tap in order to ensure a perfect hold between the body and ramp.

WARNING: The electric cable which is provided with the appliance is connected to the appliance with a type X connection and thus can be replaced with the same type of cable as that installed without using special tools. In the event of wear or damage to the mains cable, replace it with :

Type/ section of mains cable H05VV-F 3x0,75 mm2 or H05RR-F 3x0,75 mm2

WARNING: If you replace the electric mains cable the installer must have the earth conductor about 2 cm longer than the phase conductors and must also take heed of the warnings regarding electric connection.

Room ventilation – Location and venting.

ATTENTION: An exhaust fan may be used with the appliance; in each case it shall be installed in conformity with the national standards in force.

ATTENTION: Exhaust hood operation may affect other vented appliances; in each case it shall be installed in conformity with the national standards in force.

-CHANGING THE NOZZLES FOR USE WITH OTHER TYPES OF GAS: To change the nozzles of the burners use the following procedure:

Lift up the burners and unscrew the nozzles ( Fig. 9) using an adjustable spanner of 7 mm and change the nozzles with those designed for the new gas supply according to the information given in TABLE A shown below.

TABLE N°2: Adapting to different types of gas								APPLIANCE CATEGORY:			III
Burner	Type of Gas		Pressure	Nozzle		Nominal Charge				Reduced Charge		Diameter
				diameter								by-pass 1/100mm
			mbar	1/100mm	g/h	l/h	Kw		kcal/h	kw	kcal/h
	Town	G110	8	145	-	227	1,00		860	0,30	258	27 reg
Auxiliary	Natural	G20	20	77	-	95	1,00		860	0,30	258	27 reg
	Butane	G30	28	50	73	-	1,00		860	0,30	258	27
	Propane G31		37	50	71	-	1,00		860	0,30	258	27
	Town	G110	8	192	-	397	1,75		1505	0,44	378	31 reg
Semi-	Natural	G20	20	101	-	167	1,75		1505	0,44	378	31 reg
Rapid	Butane	G30	28	66	127	-	1,75		1505	0,44	378	31
	Propane G31		37	66	125	-	1,75		1505	0,44	378	31
	Town	G110	8	280	-	681	3		2580	0,75	645	42 reg
	Natural	G20	20	129	-	286	3		2580	0,75	645	42 reg
Rapid	Butane	G30	28	87	218	-	3		2580	0,75	645	42
	Propane G31		37	87	214	-	3		2580	0,75	645	42
	Town	G110	8	130	-	181	0,8		688	0,30	258	27 reg
Dual	Natural	G20	20	70	-	76	0,8		688	0,30	258	27 reg
burner	Butane	G30	28	46	211	-	0,8		688	0,30	258	27
inner	Propane G31		37	46	207	-	0,8		688	0,30	258	27
	Town	G110	8	2x300	-	885	4,4	3784		1.8	1548	65 reg
Dual	Natural	G20	20	2x110	-	419	4,4	3784		1.8	1548	65 reg
burner	Butane	G30	28	2x69	298	-	4,1	3526		1.8	1548	65
outer	Propane G31		37	2x69	293	-	4,1	3526		1.8	1548	65

CAUTION: save the orifices removed from the appliance for future use

Regulation of burners

Regulation of the "MINIMUM" on the burners

To regulate the minimum on the burners carry out the following procedure indicated below:

1)Turn on the burner and put the knob onto position MINIMUM ( small flame ).

2)Remove the knob ( Fig. 10) of the tap which is set for standard pressure. The knob is found on the bar of the tap itself.

5