Billy Goat BG1002SP specifications Troubleshooting, Before OPERATING, Make Sure

CAUTION

Reference: Label CAUTION
Part No. 830138	READ OWNER'S MANUAL

USE PROTECTION

BEFORE OPERATING, MAKE SURE:

EXHAUST ELBOW IS ATTACHED.

EXHAUST IS DISCHARGING INTO ENCLOSED CONTAINER.

HOSE IS ATTACHED.

ALL GUARDS ARE ATTACHED. OPERATING INSTRUCTION IS OBTAINED.

830138

STOP ENGINE AND ALLOW T O

COOL BEFORE REFUELING.

KEEP ENGINE CLEAN OF DEBRIS.

INSPECT MACHINE BEFORE EACH USE AND REPLACE ANY

WORN AND DAMAGED PARTS.

PROPERLY SECURE EQUIPMENT BEFORE TRANSPORTING.

NEVER SERVICE UNIT WITHOUT DISCONNECTING SPARK PLUG WIRE.

USE ONLY A QUALIFIED MECHANIC TO SER VICE THIS MACHINE.

				ABRASIVE DEBRIS WILL SHORTEN UNIT LIFE.
20	TROUBLESHOOTING		Before Requesting Service Review These Suggestions
	Problem		Possible Cause	Solution
Will not vacuum or has poor		Dirty debris bag. Nozzle height set too high or too low. Hose kit cap		Clean debris bag. Shake bag clean or wash. Adjust nozzle height.
vacuum performance.		missing. Clogged nozzle or exhaust. Excessive quantity of debris.		Check for hose kit cap. Unclog nozzle or exhaust (see page 5).
				Allow air to feed with debris.
Abnormal vibration.		Loose or out of balance impeller or loose engine.		Check impeller and replace if required. Check Engine.
Engine will not start.		Throttle in off position. Out of gasoline. Bad or old gasoline.		Check stop switches, throttle, and gasoline. Connect spark plug wire.
		Spark Plug wire disconnected. Dirty air cleaner.
				Clean or replace air cleaner. Or contact a qualified service person.
No self-propelling		Transmission not in gear. Operator's bail not engaging belt or out of		Check transmission gear selection. Check clutch cable
		adjustment. Worn out or broken belt. Broken or mispositioned belt.		adjustment and belt and chain (See page 11).
Self propelled drive will not		Sticking belt idler arm.	Belt fingers out of adjustment, bent or broken.	Check idler. Idler arm mounting screw may be too tight or too
release				loose. Check wire belt guide adjustment. Replace if broken. (see
				fig. 3 & 4 adjustment on page 11).
Noisy or broken chain		No chain lubrication. Chain out of alignment or over tensioned.		See Chain Adjustments on page 11.
Engine is locked, will not		Debris locked inside impeller. Engine problem.		See page 5, Contact an engine servicing dealer for engine problems.
pull over.

22.1

Engine Service and Warranty

WARRANTY PROCEDURE

Contact your nearest engine manufacturer's autho- rized servicing dealer.

21	Serial Plate	Record your machine model, serial number
		and date-of-purchase and where purchased

22 Please fill in the WARRANTY CARD and send the upper part to Billy Goat.

The WARRANTY terms are stated on the lower part which remains with the

user. Whenever a Billy Goat Machine is faulty due to a defect in material

and / or workmanship, the owner should make a warranty claim as follows:

The Machine should be taken to the dealer from whom it was purchased or to an authorized Billy Goat dealer.

		R
118 dB	1803 S. Jefferson P.O. Box 308
	Lee's Summit,	MO 64063 / USA
	(816) 524-9666	(816) 524-6983
	Model
	Unit (weight)
	lbs	kg

Serial No.

Engine Power

hp kw

The owner should present the remaining half of the Warranty Registration Card, or, if this is not available, the invoice or receipt.

The Warranty Claim will be filled in by the authorized Billy Goat Dealer, who will send it with the faulty part to Billy Goat headquarters.

The Quality / Service department at Billy Goat headquarters will study the claim and parts and will notify their conclusions.

The decision by the Quality / Service department at Billy Goat headquarters to approve or reject a Warranty claim is final and binding.

Note: To process a Warranty Claim, it is necessary to quote the Model & Serial number who are printed on the Billy Goat Serial Plate.

Purchase Purchased

Datefrom

BILLY GOAT INDUSTRIES INC.

1803 S.W. JEFFERSON STREET; LEE'S SUMMIT, MO 64082-2312 / USA

PHONE: 816-524-9666 FAX: 816-524-6983 www.billygoat.com

Part No. 800012 Page 12 of 12 Form No. F021402A