DL Owner’s Manual

VACUUMING OPERATION

EXHAUST DIRECTION & DISTANCE: Exhaust direction and distance are controlled by the rotation of the exhaust elbow. Typically debris is aimed to discharge to the rear of the container. The direction of discharge is adjusted by turning the crank on the exhaust elbow clamp and rotating the elbow to the desired direction.

NOTE: Elbow is heavy. Use caution when adjusting. Never stand directly under the elbow while adjusting direction of exhaust.

Never direct exhaust into an area where bystanders may cross the path of the debris.

INTAKE OPERATION: With machine running and fully assembled, move the nozzle in sweeping motions over debris. Always allow air to flow into the nozzle along with the debris. Do not completely block the nozzle when vacuuming, it will reduce performance, and increase clogging (See figure 3).

For removal of heavier debris, or debris that is stuck to the ground, rock nozzle forward to concentrate suction power around the debris (See figure 4).

ADJUSTING HOSE BOOM

Properly adjusting the boom will prevent most hose clogs from occurring and will maximize vacuum performance by keeping the hose straight and perpendicular to the housing (see fig. 5). Height adjustments are made by raising or lowering one of the attachment links to a different area on the chain.

UNCLOGGING A CLOGGED HOSE

With engine running and unit secured to a trailer, truck bed, or other similar surface, fully stretch hose in a straight line to dislodge the clog. If the clog will not clear, turn unit off, and allow engine to come to a complete stop. Remove hose and manually clear hose clog. NOTE: The clogged debris may be sharp. Always wear durable gloves when removing clog.

UNCLOGGING A CLOGGED HOUSING OR EXHAUST ELBOW

Turn engine off and wait for impeller to come to a complete stop. Disconnect spark plug wires and battery cables. Remove the hose from the housing and determine where the clog is located. If possible clear the clog through the intake opening. It may require removal of the intake adaptor (item 33) to allow access to clear the housing. If clog is in the elbow, carefully remove the elbow. Remove elbow by removing the bolts and nuts on the elbow clamp so that the plates can be removed.

NOTE: Elbow is very heavy. Do not stand directly under elbow during removal. Danger, the clog may contain sharp materials. Wearing durable gloves, clear the clog. Reconnect spark plug wire.

HOSE CARE AND TIPS

To increase hose life, periodically rotate hose and reposition nozzle and coupler on front plate of unit. This increases hose life by keeping hose from wearing only on one side.

Keep hose as straight as possible and avoid sharp bends during operation for best pick- up and to avoid clogs.

Never drag hose. Always remove and store hose before transporting unit. Store hose straight and flat to maintain flexibility for next use.

THE HOSE IS A REPLACEABLE WEAR ITEM.

Fig. 3

Fig. 4

Hose

 

Hose Band.

 

 

Stretch hose out

 

 

 

before clamping

Fig. 5

 

 

 

 

 

 

 

 

STORAGE

Turn fuel supply off when unit is not in use. Never store engine indoors or in enclosed poorly ventilated areas with fuel in tank, where fuel fumes may reach an open flame, spark or pilot light, as on a furnace, water heater, clothes dryer or other gas appliance.

If engine is to be unused for 30 days or more, prepare as follows:

Be sure engine is cool. Do not smoke. Remove all gasoline from carburetor and fuel tank to prevent gum deposits from forming on these parts and causing possible malfunction of engine. Drain fuel outdoors, into an approved container, away from open flame. Run engine until fuel tank is empty and engine runs out of gasoline. NOTE: Fuel stabilizer (such as Sta-Bil) is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow mix ratio found on stabilizer container. Run engine at least 10 min. after adding stabilizer to allow it to reach the carburetor. HOSE STORAGE: Storing hose in a covered area, out of sunlight and heat will prolong hose life. Do not store hose where it could be stepped on or where other objects could crush or damage hose.

Part No 791098

11

Form No F070207A

Page 10 Page 12
Page 11
Image 11
Billy Goat DL2500S, DL1800V owner manual Adjusting Hose Boom
Page 10 Page 12

DL1800V, DL2500S specifications

The Billy Goat DL2500S and DL1800V are powerful and efficient debris loaders, designed to tackle tough landscaping and yard maintenance jobs with ease. Billy Goat has a longstanding reputation for producing high-quality outdoor equipment, and these models exemplify that commitment to excellence.

The DL2500S is equipped with a robust 25 hp engine, providing impressive suction power to efficiently collect and transport leaves, grass clippings, and other debris from yards and gardens. Its innovative design includes a unique impeller system that maximizes airflow, enhancing the loader’s overall efficiency. The machine features a large capacity collection bag, capable of holding up to 2500 pounds of material, which minimizes downtime caused by frequent emptying. Additionally, the DL2500S boasts a heavy-duty steel construction, ensuring durability even under harsh working conditions.

On the other hand, the DL1800V offers a slightly smaller but equally powerful alternative with an 18 hp engine. This model is particularly suitable for residential and light commercial applications, where maneuverability and efficiency are key. The DL1800V is designed with a compact chassis, allowing for easy transport and storage, while still delivering strong sucking power to gather large quantities of debris quickly. It features a shredding capability that reduces the volume of collected debris, making it easier to manage and dispose of.

Both models utilize advanced technologies such as variable speed control, which allows operators to adjust the suction strength based on the conditions of the debris and terrain. This feature enhances versatility, making these loaders effective in a variety of lawn care applications. Moreover, the user-friendly controls ensure that even those with limited experience can operate them efficiently.

Another key characteristic of the Billy Goat DL2500S and DL1800V loaders is their maintenance-friendly design. Easy access points for routine checks and servicing mean that owners can keep their equipment in top working condition without hassle.

In summary, the Billy Goat DL2500S and DL1800V models stand out in the market for their powerful performance, efficient design, and user-friendly features. Whether for professional landscapers or dedicated homeowners, these debris loaders represent a reliable solution for keeping outdoor spaces clean and tidy. With their robust build and advanced technology, they are ideal assets for any landscaping operation.
Top Page Image Contents