Billy Goat KD510 specifications Troubleshooting, Engine Service and Warranty

19 PARTS LIST CONTINUED ( Continued from page 11 )

item	PARTS		KD510	QTY	KD510IC	QTY	KD510H	QTY	KD510HS	QTY	TKD510IC	QTY	TKD510H	QTY
no.	LIST	Description	Part No.		Part No.		Part No.		Part No.		Part No.		Part No.
78	BOLT CARRIAGE 5/16-18x3/4"		-	-	-	-	-	-	8024039	2	-	-	-	-
79	LINE PVC		-	-	-	-	-	-	900732	1	-	-	-	-
80
81
82
83	CONNECTOR BAG QUICK		890176	1	890176	1	890176	1	890176	1	890176	1	890176	1
84	LABEL READ OWNER'S MANUAL		890301	1	890301	1	890301	1	890301	1	890301	1	890301	1
85	TAMPER		-	-	-	-	-	-	-	-	890229	1	-	-
86	LABEL EAR/EYE BREATING		890254	1	890254	1	890254	1	890254	1	890254	1	890254	1
87

*Denotes standard hardware item that may be purchased locally.

20TROUBLESHOOTING

Problem

Before Requesting Service Review These Suggestions

Possible Cause Solution

Will not vacuum or has poor vacuum perfor-	Dirty debris bag. Nozzle height set too high or too low.	Clean debris bag. Shake bag clean or wash. Adjust
mance.	Hose kit cap missing. Clogged nozzle or exhaust.	nozzle height. Check for hose kit cap. Unclog nozzle or
	Excessive quantity of debris.	exhaust (see page 5). Allow air to feed with debris.
Poor chipping performance.	Extremely hard wood. Dull or damaged chipper blade.	Avoid extremely hard wood. Sharpen or replace
		chipper blade (see page 8).
Engine stalls or labors when chipping.	Feeding branches into chipper too rapidly. Engine	Feed branches at a slower rate. Service engine.
	service may be required.
Abnormal vibration.	Loose or out of balance impeller or loose engine.	Check impeller and replace if required. Check
		Engine.
Engine will not start.	Stop switch off (Honda only). Throttle in off position.	Check stop switches, throttle, choke position and
	Engine not in full choke position (Honda only). Out of	gasoline. Connect spark plug wire. Clean or replace
	gasoline. Bad or old gasoline. Spark Plug wire	air cleaner. Or contact a qualified service person.
	disconnected. Dirty air cleaner.Safety Interlock engaged.	Quick Disconnect not fully engaged.
Engine is locked, will not	Debris locked in chipper blade, hopper or inside	See page 5, Clearing a clogged chipper hopper.
pull over.	impeller. Engine problem.	Contact an engine servicing dealer for engine
		problems.

22.1		Engine Service and Warranty					WARRANTY PROCEDURE
							22 Please fill in the WARRANTY CARD and send the upper part to Billy Goat.
	Contact your nearest engine manufacturer's autho-
		rized servicing dealer.					The WARRANTY terms are stated on the lower part which remains with the
							user. Whenever a Billy Goat Machine is faulty due to a defect in material
21	Serial Plate		Record your machine model, serial number				and / or workmanship, the owner should make a warranty claim as follows:
			and date-of-purchase and where purchased				The Machine should be taken to the dealer from whom it was
				1803 S. Jefferson			purchased or to an authorized Billy Goat dealer.
				P.O. Box 308			The owner should present the remaining half of the Warranty
	L A			Lee's Summit,
				MO	64063 / USA		Registration Card, or, if this is not available, the invoice or receipt.
	98		R	Tel (816) 524-9666
				Fax (816) 524-6983			The Warranty Claim will be filled in by the authorized Billy Goat Dealer,
		Model			Serial No.		who will send it with the faulty part to Billy Goat headquarters.
							The Quality / Service department at Billy Goat headquarters will study
							the claim and parts and will notify their conclusions.
	LpA	Unit(Weight)			Engine Power		The decision by the Quality / Service department at Billy Goat
							headquarters to approve or reject a Warranty claim is final and
	108
		lbs.		kg	kW	rpm	binding.
Operator						min-1	Note: To process a Warranty Claim, it is necessary to quote the Model
							& Serial number who are printed on the Billy Goat Serial Plate.

Purchase Purchased

Datefrom

BILLY GOAT INDUSTRIES INC.

P.O. BOX 308 (1803 S JEFFERSON) LEE'S SUMMIT, MO 64063 / USA PHONE: 816-524-9666 FAX: 816-524-6983

Part No. 890394 Page 12 of 12 Form No. F011398B