20 | TROUBLESHOOTING | Before Requesting Service Review These Suggestions | |
| Problem | Possible Cause | Solution |
Poor air performance | Air intake or exhaust clogged. | Clear clog. | |
|
|
| |
Machine is difficult to maneuver. | Low tire air pressure. | Inflate front and rear tires to correct pressure. | |
|
|
| (See tire pressures on page 14.) |
|
|
| |
Abnormal vibration | Loose or out of balance impeller or loose | Check impeller and replace if required. Check | |
|
| engine. | Engine. |
|
|
| |
Engine will not start | Stop switches off. Choke lever not in on | Check switches, choke, gasoline and oil. Check | |
|
| position. Out of gasoline. Bad or old gasoline. | for spark with an approved tester. Clean or |
|
| Spark Plug wire disconnected. Dirty air | replace air cleaner. Contact qualified service |
|
| cleaner. | person. |
|
|
| |
Engine is locked, will not pull over. | Engine problem. | Contact your nearest engine manufacturers | |
|
|
| servicing dealer. |
Self Propelled Units Only |
|
|
|
|
|
|
|
No | Transmission not in gear. Operator's bail not | Check transmission gear selection. Check clutch | |
| engaging belt or out of adjustment. Worn out or | cable adjustment, belt and chain (See page 14). | |
| broken chain. Broken or mispositioned belt. |
|
|
|
|
|
|
Self propelled drive will not release | Sticking belt idler arm. Belt fingers bent or | Check idler. Idler arm mounting screw may be | |
| broken. | too tight or too loose. Check belt guide. | |
|
| Replace if broken. | |
|
|
|
|
Noisy or broken chain | No chain lubrication. Chain out of alignment or | See Chain Adjustments on page 14. | |
| over tensioned. |
|
|
22.1Engine Service and Warranty
Contact your nearest engine manufacturer's
authorized servicing dealer.
21 | Serial Plate | Record your machine model, serial number | |
and | |||
|
|
| 1803 S. Jefferson | |
| P.O. Box 308 | |
| Lee's Summit, | |
| MO | 64063 / USA |
R | Tel (816) | |
| ||
| Fax (816) |
ModelSerial No.
115 dB |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| ||||
|
| Unit(Weight) |
|
|
|
| Engine Power |
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Unit |
|
| kg |
|
| kW |
|
| rpm | |
|
|
| lbs. |
|
|
|
|
|
|
@
Purchase Purchased
Datefrom
WARRANTY PROCEDURE
22Please fill in the WARRANTY CARD and send the upper part to Billy Goat. The WARRANTY terms are stated on the lower part which remains with the user. Whenever a Billy Goat Machine is faulty due to a defect in material and / or workmanship, the owner should make a warranty claim as follows:
The Machine should be taken to the dealer from whom it was purchased or to an authorized Billy Goat dealer.
The owner should present the remaining half of the Warranty Registration Card, or, if this is not available, the invoice or receipt.
The Warranty Claim will be filled in by the authorized Billy Goat Dealer,who will send it with the faulty part to Billy Goat headquarters.
The Quality / Service department at Billy Goat headquarters will study the claim and parts and will notify their conclusions.
The decision by the Quality / Service department at Billy Goat headquarters to approve or reject a Warranty claim is final and
binding.
Note: To process a Warranty Claim, it is necessary to quote the Model & Serial number who are printed on the Billy Goat Serial Plate.
BILLY GOAT INDUSTRIES INC.
P.O. BOX 308, 1803 S JEFFERSON LEE'S SUMMIT, MO.
Part No. 430149 | Page 16 of 16 | Form No. F110802A |