Billy Goat TKD505H, TKD505ICQ specifications 108

19		PARTS LIST CONTINUED	( Continued from page 11 )
	Item	Description		TKD505H	QTY	TKD505ICQ	QTY	* Denotes
				Part No.		Part No.
	No.							standard
	78							hardware item
	79							that may be
	80							purchased
	81							locally.
	82
83		CONNECTOR BAG QUICK		890176	1	890176	1
	84	LABEL READ OWNER'S MANUAL		890301	1	890301	1
	85	TAMPER		890229	1	890229	1
	86	LABEL EAR EYE BREATHING		890254	1	890254	1
87		PLATE BRACE ADJ. KD / TKD		900756	1	900756	1

20 TROUBLESHOOTING

Problem

Before Requesting Service Review These Suggestions

Possible Cause Solution

Will not vacuum or has poor vacuum perfor-					Dirty debris bag.	Nozzle height set too high or too low.			Clean debris bag. Shake bag clean or wash. Adjust
mance.					Hose kit cap missing. Clogged nozzle or exhaust.				nozzle height. Check for hose kit cap. Unclog nozzle or
					Excessive quantity of debris.				exhaust (see page 5). Allow air to feed with debris.
Poor chipping performance.					Extremely hard wood. Dull or damaged chipper blade.				Avoid extremely hard wood. Sharpen or replace
									chipper blade (see page 8).
Engine stalls or labors when chipping.					Feeding branches into chipper too rapidly. Engine				Feed branches at a slower rate. Service engine.
					service may be required.
Nozzle scrapes ground in lowest height					Nozzle height out of adjustment.				Adjust nozzle height. (See Nozzle height fine
setting.									adjustment for hard surface use on page 5).
Abnormal vibration.					Loose or out of balance impeller or loose engine.				Check impeller and replace if required. Check
									Engine.
Engine will not start.					Stop switch off (Honda only). Throttle in off position.				Check stop switches, throttle, choke position and
					Engine not in full choke position (Honda only). Out of				gasoline. Connect spark plug wire. Clean or replace
					gasoline. Bad or old gasoline. Spark Plug wire				air cleaner. Or contact a qualified service person.
					disconnected. Dirty air cleaner.
Engine is locked, will not					Debris locked in chipper blade, hopper or inside				See page 5, Clearing a clogged chipper hopper.
pull over.					impeller. Engine problem.				Contact an engine servicing dealer for engine
									problems.
22.1		Engine Service and Warranty					22		WARRANTY PROCEDURE
								Please fill in the WARRANTY CARD and send the upper part to Billy Goat.
	Contact your nearest engine manufacturer's autho-
		rized servicing dealer.						The WARRANTY terms are stated on the lower part which remains with the
								user. Whenever a Billy Goat Machine is faulty due to a defect in material
21	Serial Plate		Record your machine model, serial number					and / or workmanship, the owner should make a warranty claim as follows:
			and date-of-purchase and where purchased					The Machine should be taken to the dealer from whom it was
				1803 S. Jefferson				purchased or to an authorized Billy Goat dealer.
				P.O. Box 308				The owner should present the remaining half of the Warranty
	L A			Lee's Summit,
			R	MO	64063 / USA			Registration Card, or, if this is not available, the invoice or receipt.
	98			Tel (816) 524-9666
				Fax (816) 524-6983				The Warranty Claim will be filled in by the authorized Billy Goat Dealer,
		Model			Serial No.			who will send it with the faulty part to Billy Goat headquarters.
								The Quality / Service department at Billy Goat headquarters will study
								the claim and parts and will notify their conclusions.
	LpA	Unit(Weight)			Engine Power			The decision by the Quality / Service department at Billy Goat
								headquarters to approve or reject a Warranty claim is final and
	108
		lbs.	kg		kW	rpm		binding.
Operator						min-1		Note: To process a Warranty Claim, it is necessary to quote the Model
								& Serial number who are printed on the Billy Goat Serial Plate.

Purchase Purchased

Datefrom

BILLY GOAT INDUSTRIES INC.

P.O. BOX 308 (1803 S JEFFERSON) LEE'S SUMMIT, MO 64063 / USA PHONE: 816-524-9666 FAX: 816-524-6983

Part No. 890313 Page 12 of 12 Form No. F010396D