This telephone gives you the possibility to use the special services services of your network provider.
When pressing the RECALL button, the phone generates a line interruption and the length depends on your Flash Time setting.
In standby mode, press SET/STO button.
ÖThe display shows ' SET 1 DATE '.
Press UP or DOWN button until the display shows 'SET 3 FLASH'. Press SET/STO to confirm.
Press UP or DOWN button to select 100 (default),300, 600, or 1000.
Press SET/STO button to confirm the setting.
Ö The display shows ' SET 1 DATE ' , you can continue with |
programming, or press DELETE button to return to |
Stored3 number
Storing a 1 Number in (0-9)
two-touch 2 memories
3
Lift up Handset or press the SPEAKERPHONE button,
press M1,M2,M3 buttons.
ÖThe number dials automatically.
In standby mode, Key in the telephone number you wish to stored.
ÖUp to a maximum 16 digits.
Press SET/STO button.
Press the (0-9) button to store the number in the
selected memories.
After the Guarantee has expired
If the unit is no longer under Guarantee, first follow steps 1 and 2 as for repair under Guarantee. Then …
3.Call our Service Department on 0845 345 9677 and ask for a quotation of the repair charge and details of where to send your Lyris 410 for repair.
4.Make sure you include with your Lyris 410:
your name and address. a cheque or postal order for the value of the repair charge.
5.Return your Lyris 410 to the address given by the Service Department.
8.Technical details
Standard Lyris 410 Telephone
Temperature range Operating 0 ºC to 40 ºC
Storage -20 ºC to 60 ºC
Making a 1 call
2
3
To answer a call
To adjust the speakerphone volume
To end a call
To switch between the Handset and the Speakerphone
Lift the Handset, listen for a dial tone.
ÖThe display shows ' 00-00'.
Dial the telephone number you wish to call.
ÖThe display shows the number as you dial(maximum of 14 digits will be shown).
To end the call, return the Handset to the Base unit.
When the phone rings;
Lift the handset or press the SPEAKERPHONE button on the Base unit.
ÖThe Call timer starts about 7 seconds after going on line.
During a call;
Adjust the volume of the speakerphone to your comfortable volume level using the SPEAKERPHONE volume switch located at
the right side of the Base unit.
Replace the Handset on the Base unit cradle or press the SPEAKERPHONE button on the Base unit.
ÖThe SPEAKERPHONE light indicator will turn OFF.
During a phone conversation through the Handset, press the SPEAKERPHONE button to speak hands-free.
The Speakerphone light will turn on, but conbrtdsyion remains through the Handset until the Handset is speakerphone replaced on the Base unit cradle. while in speakerphone mode, lift the Handset to enable a private conversation.
| (0-9) | C | w:-;; <0- `Y`bdj *=<<76 Ztmt[ |
| C | r-A 16 <0- 5-57:A 47+~<176 6=5*-: Z_]h[ |
| two-touch |
| memories | Ö The number dials automatically. |
6. Caller Display Operation
VERY IMPORTANT:
To use Caller Display you must first subscribe to your network provider's Caller Diaply service. If you subscribe to a Caller Display service, you can see the phone number of the person calling you before you answer. The caller display information includes:
The caller's number | | The date and time of the call |
| | |
Condition of Incoming Caller Information | | LCD Screen will display |
It is a duplicate one | | REP |
It is a new one | | NEW |
It has exceeded the range of the service | | UNAVAILABLE |
It is a secret one | | WITHHELD |
It may not be nicety for the reason of outside | ERROR |
There is a voice information in your mailbox (This function is available only when you have applied for this service from your telecommunication network)
Caller Display list
Lyris 410 dynamically stores up to 30 groups (12digits)incoming information.
If a call is received when the Call list is full, then the new entry will replace the oldest one.
Operation on other countries’ PSTN termination points cannot be guaranteed.
BINATONE TELECOM PLC
1 Apsley Way London NW2 7HF,United Kingdom. | | |
Tel: +44(0) 20 8955 2700 Fax: +44(0) 20 8344 8877 | |
e-mail: binatoneuk@binatonetelecom.co.uk | | . |
________________________________________ |
EC Declaration of Conformity |
We the manufacturer / Importer : | Binatone Telecom Plc |
| 1 Apsley Way London |
| NW2 7HF, United Kingdom. |
Declare under our sole responsibility that the following product |
Type of equipment: | Corded phone |
Model Name: | Lyris 410 |
Country of Origin: | China | |
Brand: | Binatone | |
complies with the essential protection requirements of R&TTE Directive 1999/5/EC on the approximation of the laws of the Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility (EMC) and the European Community Directive 2006/95/EC relating to Electrical Safety.
Assessment of compliance of the product with the requirements relating to the essential requirements according to Article 3 R&TTE was based on Annex III of the Directive 1999/5/EC and the following standard:

EMC: | EN 55022:2006 | Waste electrical products must not be |
disposed of with household waste. |
EN 55024:1998+A1+A2 | This equipment should be taken to |
|
| your local recycling centre for safe |
Electrical Safety: EN 60950-1:2006 | treatment. |
|
The product is labelled with the European Approval Marking CE as show. Any Unauthorized modification of the product voids this Declaration.
Manufacturer / Importer
Last 1
Number
Redial 2
Mute 1 Function
2
Inserting a
Pause in
the dialing
sequence 1
2
Lift the Handset or press the SPEAKERPHONE button on
the Base unit.
Press LNR button.
ÖThe phone automatically dials the last number you called (maximum of 32 digits).
During a call press MUTE
button.
ÖWhen the mouthpiece is muted, the person at the other end of the call cannot hear you but you can hear his side.
To get back to the call, press MUTE
button again to release.
For some switchboard system, an access number must be dialed (usually an 8 or 9) to get another dial tone and an outside line.
Pressing PAUSE button immediately after the access number, a pause of about 3.6 seconds will be entered, and the desired number can be dialed immediately.
Press PAUSE button to insert a pause when dialing or
Viewing the 1
Caller
Display list
2
To return 1 a call
2
To delete Caller Display record
In standby mode, press UP or DOWN Dutton.
ÖThe display shows the most recent record.
If there are no Caller Display records, the display will show
' 00 CALL'
Press UP or DOWN again to scroll to the next Caller Display record.
When the Caller Display record is displayed. Press LNR button.
Lift the handset or press the SPEAKERPHONE button on the Base unit.
ÖThe phone automatically dials out the displayed record.
When the Caller Display record is displayed.
Press DELETE button will delete the Caller Display record.
ÖThe display shows the next Caller Display record.
Press and hold DELETE button 3 seconds, all the Caller Display records will be deleted.
ÖThe display automatically return to standby mode.
(signature of authorized person)
| London, |
Signature: | Place & Date: 8th Mar, 2009 |
Connection and conditions for use
You can connect your Lyris 410 phone to a direct exchange line (DEL) - a line connected to a local exchange, with its own phone number; to an extension socket connected to a DEL; or to an extension on an approved compatible PBX. Do not connect the Lyris 410 phone as an extension to a pay phone.
The ringer equivalence numbers (RENs) of all instruments (phones, fax machines, etc.) connected to an exchange line must not add up to more than 4 - otherwise, one or more of them may not ring and/or answer calls correctly.
The Lyris 410 phone has a REN of 1, and most other telephones have a REN of 1 unless marked otherwise.
Use on PBX
Storing a 1 Number in
M1,M2,M3 memories 2
2
If you are using your Lyris 410 phone on a PBX, and the PBX user guide tells you to press RECALL;
Press R (RECALL) button on your Lyris 410 phone.
In standby mode, Key in the telephone number you wish to stored.
ÖUp to a maximum 16 digits.
Press SET/STO button.
The Binatone Lyris 410 is guaranteed for 12 months from the date of purchase shown on your sales receipt. The Guarantee does not cover damage by misuse or negligence, or by excessive voltages - for example, faults on the telephone line, or lightning. This does not affect your statutory rights.
Please keep your sales (till) receipt - this is your guarantee. You should also keep the original
packaging material.
In the unlikely event that you need to return your Lyris 410 to our Repair Centre while it is under guarantee, there will be a £5 handling charge.
While the unit is under Guarantee
1.Where to find it
2. Installation
3. Wall mount installation
4. Setting up your phone
5. Telephone operation
6. Caller display operation
7. Guarantee and service
8. Technical details
Pressing buttons on your phone
If you need help …
The Binatone Help Line is
available from 9.00 am to
5.00pm, Monday to Friday, on 0845 345 9677
Calls are charged at Local Call rate.
3
3
Press M1.M2 and M3 button to stored.
1.Disconnect the Base unit from the telephone line and the mains electricity supply.
2.Pack up all parts of your Lyris 410, using the original packaging. Remember to include the mains adapter
3.Return the unit to the shop where you bought it, making sure you take your sales receipt.
When the instructions in this user guide tell you simply to ‘press’ a button, this means that you should press the button briefly, then release it.
When the instructions tell you to ‘press and hold’ a button, this means you should keep the button pressed until the display changes and/or you hear a tone.
UK BTP Ver 2.0 May 2009