Spirit 410 Corded Telephone
Installing (or Replacing) the Battery
IMPORTANT - Before removing the battery compartment cover,always make sure the base unit is disconnected from the telephone line.
Unpacking your phone
In the box you will find:
•Base Unit
•Handset
•Coiled Handset cord
•Telephone line cord for Base unit
•User manual
Keep the packing materials in a safe place in case you later need to transport the unit
Install 2 pcs of Alkaline AAA batteries into the battery compartment and place back the cover before use.
Note: 1) Please do NOT use Rechargeable batteries in this phone.
2),-8806: 27 458 24.39/0/ 810 9428
?GDL QGD A@QQDOT HP JMS< 
will show up of the CHPNJ@T PBODDL= >E TMR CM LMQ ODNJ@BD QGD A@QQDOHDP< QGDT SHJJ ADBMKD QMQ@JJT CHPBG@OFDC @LC TMRO CHPNJ@T PBODDL SHJJ LMQ SMOI=
SIZE | AAA | SIZE | AAA |
SIZE | AAA | SIZE | AAA |
9
BE CAREFUL to check that there are no electrical wires hidden in the wall. Fix two screws (supplied with the unit) at the marked locations, leaving approximately 7mm between the wall and the the screw head.
Hang the cradle unit on the screws using the wall mount slots.
You may need to remove the telephone from the wall and tighten the screws so that the cradle is securely fixed and does not wobble . Place the Handset on the
cradle with the parking hook on the cradle arranged to fit in the parking recess under the earpiece on the Handset.
Keep your sales (till) receipt, which is your guarantee.
11
12
1. | LCD Screen |
2. | Ringer light indication |
3. | M1,M2,M3 Memory buttons |
3. Desk/Wall mount installation
Desk Mount | To place the Spirit 410 on a desk, connect the stand to |
| the bottom of the phone in the slots near the rear of the base |
| as shown below . |
4. Setting up your phone
Press the SET/STO button to enter the menu and then use UP or DOWN buttons to cycle through the following options:
SET 1 DATE | SET 2 LCD | SET 3 FLASH |
Note: The system will time out if you leave more than 8 seconds between key presses.
4. | Scroll Up & Down buttons |
5. | Delete button |
6. | Set/Store button |
7. | Memory button |
8. | LNR(Last Number Redial) button |
9. | Speakerphone button |
10. | Mute button |
Insert the rigid clips of the stand into the slots on the bottom of the phone (near the rear of the base). Press down firmly until
You will need to set the correct time and date so they can be displayed correctly on the display.
If you subscribe to a Caller Display service, the time and date will be set automatically on receipt of your first incoming call.
In standby mode, press SET/STO button.
ÖThe display shows ' SET 1 DATE '.
Press SET/STO button to confirm.
ÖThe 'year' icon will be blinking.
11.R(Recall) button 12.Pause button
the flexible clips clicks into place.
To remove the stand, (1) pinch the flexible clips, (2) pull back the stand, and then (3) slide up and forward (3) as shown below.
3Press UP or DOWN button to set the year.
4 | Press SET/STO button to confirm. |
ÖThe 'month' icon will be blinking.
Important note---back up batteries
The Spirit 410 requires 2 x 1.5V AAA size Alkaline batteries installed into the battery compartment before use. Warning: The caller display will not work without batteries installed.
2. Installation
To place the Spirit 410 on a wall, connect the stand to the
Wall Mountbottom of the phone in the slots near the front of the base cover as shown below.
5Press UP or DOWN button to set the month.
6 | Press SET/STO button to confirm. |
ÖThe 'date' icon will be blinking.
7 | Press UP or DOWN button to set the date. |
8 | Press SET/STO button to confirm. |
ÖThe 'hour' icon will be blinking.
9 | Press UP or DOWN button to set the hour. |
1.Locating the Base unit
The Base unit should be placed on a level surface, in a position where:
Setting up continue...
the telephone line cable will reach your telephone line socket or extension socket.
it is not close to a sink, bath or shower, or anywhere else where it might get wet.
it is not close to other electrical equipment - fridges, washing machines,
Press SET/STO button to confirm.
ÖThe 'minute' icon will be blinking.
Press UP or DOWN button to set the minute.
microwave ovens, TVs, fluorescent lights, etc.
2.Plug the coiled handset cord into the Handset.
Plug the other end into the jack on the left side of the Base unit.
3.Place the Handset in the Base unit.
Always use the
Make sure the plugs click into place. 
Desk/Wall mounting continue...
Insert the rigid clips of the stand into the slots on the bottom of the phone ( near the front of the base). Press down firmly until the flexible clips clicks into place.
To remove the stand, (1) pinch the flexible clips, (2) pull back the stand, and then (3) slide up and forward as shown below.
Press SET/STO button to confirm the setting.
ÖThe display shows ' SET 2 LCD ' , you can continue with programming,or press DELETE button to return to standby mode.
In standby mode, press SET/STO button.
ÖThe display shows ' SET 1 DATE '.
telephone line cord supplied
with your
Spirit 410 phone. Other telephone line cords may
to Modular not work. Wall jack
4.Plug the telephone line cord
free end into a modular wall jack. Press the cable into the groove so that the Base unit stands level.
5.Lift the Handset and check for Dial tone in the earpiece.
Mark two points on the wall that are 92mm apart to lay the fixing centers as shown below.
Press UP or DOWN button until the display shows 'SET 2 LCD'.
Press SET/STO to confirm.
Press UP or DOWN button to select your comfortable display viewing level (1~8).The default setting is 3.
Press SET/STO button to confirm the setting.
ÖThe display shows ' SET 2 LCD ' , you can continue with programming, or press DELETE button to return to standby mode.