When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
1.Read all instructions before using the appliance.
2.To avoid fire or shock hazard, plug the appliance directly into a 120V AC electrical outlet.
3.The heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front of the heater and keep them away from the sides and rear.
4.DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or the like. Arrange cord away from traffic area and where it will not be tripped over.
5.This heater is not intended for use in bathrooms, laundry areas and similar indoor location. NEVER locate heater where it may fall into a bathtub or other water container.
6.Extreme caution is necessary when any heater is used by, or near children or invalids, and whenever the heater is left operating and unattended.
7.Always unplug the heater when not in use.
8.When unplugging, be sure to pull by the plug and not the cord.
9.DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
10.DO NOT operate heater with a damaged cord or plug, or after the heater malfunctions, has been dropped or damaged in any manner. Return appliance to manufacturer for examination, electrical or mechanical adjustment, or repair.
11.A heater has hot and arcing or sparking parts inside. DO NOT use it in areas where gasoline, paint, or flammable liquids are used or stored.
12.Use appliance only for intended household use as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. The use of attachments not recommended or sold by the manufacturer may cause hazards.
13.DO NOT use outdoors.
14.To prevent a possible fire, DO NOT block air intakes or exhaust in any manner. DO NOT use on soft surfaces, like a bed, where openings may become blocked.
15.To disconnect heater, turn controls to OFF, then remove plug from outlet.
16.Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire. However, if you have to use an extension cord, the cord shall be No. 14 AWG minimum size and rated not less than 1875 watts.
17.If the heater will not operate, see specific instructions on Auto Safety Shut-off.
18.DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. The inside of the unit contains no user serviceable parts. All servicing should be performed by qualified personnel only.
19.Discontinue use if plug or outlet is hot. It is recommended that the outlet be replaced if plug or outlet is hot to touch.
PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS
TECHNICAL SPECIFICATIONS
•Amps: 12.5
•Wattage: 1500W (+5% –10%)
•Working voltage: 120V AC/60Hz
ASSEMBLY INSTRUCTIONS
Unpack your heater from the box, being careful to remove all parts from plastic bags and remaining packaging. Please save the carton for off-season storage.
Your heater is packed with separate base in the box. Carefully remove all parts from plastic bags. To prevent scratches, place all parts onto a cloth before assembly. Follow the below instructions for Base assembly:
Base Assembly
Step 1: If the base is in two halves, snap them together by sliding slots of one base half into slots of second base half. Refer to Figure 1.
Step 2: Run the power cord through the center of the assembled base. To assemble the base to the unit (either one or two-piece base) first make sure the side marked “Rear” is facing the back of the heater. Line up holes of the base with holes on bottom of heater housing, and secure with 4 provided screws. Refer to Figure 2.
Step 3: Lace the power cord through the cord minders on the underside of the base. Refer to Figure 3.
Step 4: Turn the heater right side up on a flat level surface prior to beginning operation.
Remote Control
Unpack the remote control from box. This includes one lithium battery, CR2025/3V. Please note this remote control will not work through walls. Remove battery before discarding the remote.
NOTE: REMOVE THE PROTECTIVE COVER FROM THE BATTERY PRIOR TO BEGINNING OPERATION.
Battery Replacement
1.Locate the battery cover on the back of the remote control handset. Slide the battery cover out with your thumb.
2.Place battery into battery compartment.
3.Slide battery cover closed.
4.For your convenience, a remote control holder is integrated into the back of the heater housing.
NOTES:
•THIS PRODUCT CONTAINS A BUTTON BATTERY. IF SWALLOWED, IT COULD CAUSE SEVERE INJURY IN JUST 2 HOURS. SEEK MEDICAL ATTENTION IMMEDIATELY.
•Remove the battery from the equipment when it is not being used for an extended period of time.
•Remove the used battery promptly.
•Do not discard used batteries into household trash containers. Contact your local government for disposal or recycling practices in your area.
FCC STATEMENT
Potential for Radio/Television interference
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
communications. However, there is no guarantee that the interference will not occur in a particular installation. If the product does cause harmful interference to radio or television reception, which can be determined by turning the product on or off, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the product and the receiver.
•Connect the product into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
•Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Figure 4 | | | |
E | D | C | B | A |
| | A | Control Buttons |
| | B | LCD Display | |
| | C | Dial Wheel | |
| | D | Power Light | |
OPERATING INSTRUCTIONS
1.Place heater on a firm, level surface.
2.Plug heater into a standard outlet. Once plugged in, the Power Light will illuminate.
NOTE: Avoid overloading your circuit by not using other high wattage appliances in the same outlet. At 1500 watts, this unit draws 12.5 Amps.
3.Operate heater by pressing the Power Button ( 
) and selecting modes and settings according to preference. NOTE: Remove the plastic film from the control panel before using (if included).
Power On/Off
Press the Power On/Off Button to turn the heater on. Once on, the heater will run in the Max Heat mode and the Stay On icon will appear on the LCD Display. Press the Power On/Off button to manually turn off the heater at any setting.
NOTE: The Power Light will remain illuminated while unit is plugged in.
Mode Selection
Select your desired heat settings by pressing the corresponding buttons as located on your heater or press the Mode button on remote control to cycle through the heat settings. An indicator light will illuminate next to each button to indicate that the selected setting/mode is activated.
Fan Only Setting
Press the Fan Only Button to run the heater without heat output. The Stay On icon will appear on the LCD Display.
– HIGH Heat Setting
Press the Max Heat Button to run the heater continuously at 1500W. The Stay On icon will appear on the LCD Display.
Eco-Smart™ Setting
Thermostat Control
Your heater is equipped with a digital thermostat that allows you to set your heater to a precise comfort level by turning the Dial Wheel on the control panel or pressing the arrow buttons on the remote control:
Turn the Dial Wheel to activate. The Thermostat icon (
) will appear on the LCD Display.
To preset a precise comfort level, turn the Dial Wheel to adjust the temperature from 85°F to 65°F (Default: “85”). The LCD Display will show the selected temperature reading. When the preset temperature is reached, the heater will shut off and cool down for 15 seconds. When the room temperature drops below the preset temperature, the heater will automatically turn on again to maintain the preset temperature level.
FrostProtect™ Setting
Your heater is equipped with FrostProtect™. The heater will turn on automatically when the room temperature drops below 40°F. To activate FrostProtect™, turn the Dial Wheel to
show “40” and the FrostProtect™ icon (
) will appear on the LCD Display.
NOTE: It is normal for the heater to cycle on and off to maintain the preset temperature. Raise the thermostat setting or operate in Stay On mode to prevent the heater from cycling. When the preset temperature is reached or when the heater is shut off, the fan will run for 15 seconds without heat. This cool down process ensures an accurate and consistent temperature reading.
NOTE: To shut the heater off at any setting, press the Power
Button (
) until the LCD Display goes off. The heater will cool down for 15 seconds, and the Fan Only indicator light will blink in Amber until cool down is completed. The digital thermostat has memory; it will remember the last temperature setting before the heater is turned off. However,
Oscillation
Press the Oscillation Button ( 
) on control panel or remote control to activate or stop the oscillation feature.
NOTE: Please do not manually turn the heater on the base. It is designed to turn only by motorized oscillation.
Timer
Your heater is equipped with 24-Hour Auto Shut-off Timer feature. This allows you to program your heater to shut off automatically after running a defined time interval (from 0 to 24 hours).
1.Press the Timer Button (
) once. The indicator light will begin to blink for 5 seconds. The LCD Display will show “0” and the “Hr” icon.
2.Turn the Dial Wheel on the control panel to adjust from 0 to 24 to select your desired time interval for the heater to shut-off automatically. The selected hour will appear on the LCD Display, and then the Timer indicator light will stop blinking in 3 seconds to indicate that the selected timer is activated. The LCD Display will return to show the preset temperature and mode setting.
3.To cancel the Timer feature, press the Timer Button (
) twice within 5 seconds, the Timer indicator light will go off.
NOTE: The timer does not work with the FrostProtectTM Setting.
CLEANING/MAINTENANCE
Always unplug the heater before cleaning and allow the heater to cool down.
1. | Clean the unit with a soft cloth moistened with a mild |
| soap and water solution. |
2. | NEVER use abrasive or flammable solvents to clean the |
| unit. |
3. | After cleaning, be sure to completely dry the unit with a |
AUTO SAFETY SHUT-OFF
This heater is equipped with a technologically-advanced safety system that requires the user to reset the heater if there is a potential overheat situation. When a potential overheat temperature is reached, the system will automatically shut the heater off. It can only resume operation when the user resets the unit.
If the heater shuts down and the Power Light is flashing:
1.Stand the heater upright.
2.Unplug the heater and allow 30 minutes for the heater to cool down.
3.After 30 minutes plug the heater in and operate normally.
4.If the heater does not work normally, repeat steps 1, 2 and 3 again.
NOTE: If the heater is plugged in again and Power On/Off Button is pressed within the 30-minute cool down period, heater will run at Max Heat setting, but shut down in 2 seconds with the Power Light flashing. Please repeat the above 4 steps to reset the heater again and ensure to allow sufficient time for the thermostat to cool down.
Tip Over Shut-Off:
When the unit is accidentally knocked over, it will instantly shut off and the Power Light will flash. The unit may also shut off if it is moved or bumped. To reset, simply place the heater in an upright position, the Power Light will stop flashing and it will operate normally.
NOTE: If unit does not turn on when placed in the upright position, press Power On/Off Button once and heater will resume operation.
