SmartTouch™
Cool Moisture
Humidifier
MODEL BCM7203
BCM7203RC
HUMIDIFIER SAFETY
PLEASE READ AND SAVE THESE IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
1.Read all instructions before using the appliance.
2.To avoid fire or shock hazard, plug the appliance directly into a 120V AC electrical outlet.
3.Keep the cord out of heavy traffic areas. To avoid fire hazard, NEVER put the cord under rugs, near heat registers, radiator, stoves, or heaters.
4.DO NOT place humidifier near heat sources such as stoves, radiators, and heaters. Do locate your humidifier on an inside wall near an electrical outlet. The humidifier should be at least 4 inches (10 cm) away from the wall for best results.
5.NEVER place humidifier in an area where it is accessible to children. NEVER use humidifier in a closed room, particularly where a child may be sleeping, resting, or playing (a closed room may result in excessive humidity).
6.WARNING: Do not attempt to refill humidifier without first unplugging the unit from its electrical outlet. Failure to heed this warning may cause personal injury.
7.NEVER place anything over moisture outlet when unit is running.
8.NEVER drop or insert any object into any openings.
9.DO NOT operate any appliance with a damaged cord or plug, if the appliance malfunctions, or if it has been dropped or damaged in any manner. Return appliance to manufacturer for examination, electrical or mechanical adjustment, or repair.
10.Use appliance only for intended household use as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. The use of
®
water reservoir and moving the unit.
16.This humidifier requires daily and weekly maintenance
to operate appropriately. Refer to daily and weekly cleaning procedures. Use only cleaners and additives recommended by the manufacturer.
17.NEVER use detergents, gasoline, glass cleaner, furniture polish, paint thinner, or other household solvents to clean any part of the humidifier.
18.Excessive humidity in a room can cause water condensation on windows and some furniture. If this happens, turn the humidifier OFF.
19.Do not use humidifier in an area where humidity level is in excess of 50%. Use a hygrometer, available at your local hardware store or through Bionaire, to measure the humidity.
20.DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. The inside of the unit contains no user serviceable parts. All servicing should be performed by qualified personnel only.
21.Never place humidifier housing under water flow or immerse in liquids.
22.Do not plug in the cord with wet hands: electric shock could result.
23.Do not pour water in any openings other than the water tank.
24.To prevent damage to surfaces, do not place humidifier under overhanging surfaces.
25.NEVER operate unit without water in the tank. 26.Use both hands when carrying full tank of water.
27.Do not move unit after it has been used until unit cools completely.
PLEASE SAVE THESE INSTRUCTIONS
CONSUMER SAFETY INFORMATION
This appliance has a POLARIZED AC
PLUG (one blade is wider than the other).
rating of the extension cord must be equal to or greater than the rating of the humidifier. Care must be taken to arrange the extension cord so that it will not drape over the countertop or tabletop where it can be pulled on by children or accidentally tripped over.
PLEASE READ AND SAVE
THESE IMPORTANT
SAFEGUARDS
Consumer Safety Information:
NOTE: This is an electrical appliance and requires attention when in use.
NOTE: If moisture forms on the walls or windows of the room, turn off the humidifier. The room already has plenty of humidity and additional moisture may cause damage.
NOTE: DO NOT block air inlet or outlet.
HOW COOL MIST WORKS:
Your Bionaire® Cool Mist humidifier draws dry air through the rear air intake grill area. This air is then passed through 2
NOTE: This humidification system provides a cool, invisible moisture output. It is normal not to see the mist.
NOTE: A humidity level below 20% can be unhealthy and uncomfortable. The recommended humidity level is between
PRE-OPERATING INSTRUCTIONS:
1. | Be sure the humidifier is switched to OFF and the unit |
| is disconnected from the electrical outlet. |
2. | Select a location for your humidifier, on a flat surface, |
| about 4 inch (10 cm) away from the wall. DO NOT |
| place the humidifier on a finished floor or near furniture, |
| which can be damaged by moisture or water. Place on |
3. Plug the power cord into a 120V AC electrical outlet.
Figure 1 |
| B | C | |||
|
|
|
|
| D | |
|
| A |
|
| E | |
|
|
| ||||
|
|
|
|
| F | |
|
|
|
| |||
| A. Water Tank | E. SmartTouch™ | ||||
| B. Carry Handle | Control Panel |
| |||
| C. FiltercheckTM Indicator | F. Humidifier Base |
| |||
| D. Humidifier Housing |
|
| |||
|
|
|
|
|
|
|
OPERATING INSTRUCTIONS:
Your humidifier is equipped with a technologically advanced SmartTouch™ Electronic Humidistat. You can set the humidifier to run continuously in manual mode or set the SmartTouch™ Electronic Humidistat to your desired humidity setting. The SmartTouch™ Electronic Humidistat will automatically turn the humidifier ON or OFF, depending on the preset comfort level. The comfort level ranges between 35% and 55% relative humidity.
Manual Mode Instructions:
1.Plug the humidifier into a 120V AC electrical outlet.
2.To start the unit, push the MODE/OFF button once for the HIGH manual setting. (See figure 2.)
3.Press the button again for the LOW manual setting. (See figure 2.)
4.To stop the unit, press and hold the button for two seconds, or keep pressing the button until all the humidity indicators are OFF.
NOTE: In Manual Mode, only the LOW or HIGH power light will be lit.
SmartTouch™ Humidistat Instructions:
NOTE: The SmartTouch™ Humidifier has memory. This means that when you turn the unit back on, it will be at the last setting the humidifier was set at.
If you do not plan to use the humidifier for two or more days, make sure any residual water is drained from the water tank, base and wick filter to prevent algae or bacteria growth.
| Figure 2 |
|
|
|
|
|
|
|
|
| A |
| B | |
|
|
|
|
|
|
|
| C | |
| A. Set Humidity Lights |
|
|
|
|
|
|
| |
| B. Speed Setting Lights |
|
|
|
|
| B | ||
| C. Mode/Off Button |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
SmartTouch™ REMOTE INSTRUCTIONS
(For BCM7203RC-CN only)
1.Insert 2 AAA batteries into back of remote control.
2.Press the SmartTouch™ button on remote to begin operation.
3.Use the remote to control the same features as the base unit.
NOTE: Do not mix new and old batteries. Do not mix alkaline,standard
REPLACING THE FILTERS:
Through normal use, waterborne minerals and sediment become trapped in the wick filters. The harder your water, the greater the amount of minerals in the water, and the more often you will need to change your filters.
You will be able to monitor the life of the filters in your humidifier by checking the FilterCheckTM Indicator. The FilterCheckTM Indicator will only read the filter condition when the humidifier is in operation.
become trapped on your filters. At this point, you should replace your filters. It is important to change your filters as indicated to obtain stated performance level.
To replace the filter, follow the steps below.:
1.Push the SmartTouch™ button (MODE/OFF) for 2 seconds to turn the unit OFF and disconnect from the electrical outlet.
2.Remove the tank and main housing to access the base.
3.Remove the wick holder from the base of the humidifier.
4.Remove each individual wick and discard. Do not remove rivet, replacement wicks come equipped with rivets for easy replacement.
5.Follow the weekly cleaning instructions.
6.Insert new filters into each section of the wick holder making sure the rivet attaches to the wick holder securely.
7.Do not use wicks without rivets as they will not produce the unit's intended output.
8.Replace the wick holder into the base (it can only go in by following the arrow indicator) and replace main housing and then tank.
9.Repeat Operating Instructions steps.
It will take about 30 minutes for the humidifier to reach maximum output.
You can purchase replacement filters (Model BWF100) by calling
It is recommended that a replacement filter is purchased for uninterrupted use.
CLEANING/MAINTENANCE INSTRUCTIONS:
Humidifiers provide comfort by adding moisture to dry, heated indoor air. To benefit most from the humidifier and avoid product misuse, follow all instructions carefully. Please note that this is an electrical appliance and requires attention when in use.
In addition, if you do not follow the recommended care and maintenance guidelines,
Read instructions before operating.
Retain for future reference.
Instruction Leaflet
☎
attachments not recommended or sold by Bionaire may cause hazards.
11.DO NOT use outdoors.
12.Always place humidifier on a firm, flat, level surface. (4 inches from wall).A waterproof mat or pad is recommended for under the humidifier. NEVER place it on a rug or carpet, or on a finished floor that may be damaged by exposure to water or moisture.
13.DO NOT allow the moisture outlet to directly face the wall. Moisture could cause damage, particularly to wallpaper.
To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician
to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS SAFETY FEATURE IN ANY WAY.
a |
FILLING THE WATER TANK:
1. Remove the tank from the base of the humidifier and |
bring to the faucet. Turn the tank upside down and |
twist off the tank cap by turning counter clockwise. Fill |
tank with cool, fresh tap water. DO NOT fill with warm |
water as this may cause leaking. Replace the cap on |
tank FIRMLY. |
To take advantage of the SmartTouch™ Electronic Humidistat, press the MODE/OFF button until the speed is set in either the HIGH or LOW setting, and the desired Humidity is set. When the humidity level rises above the set humidity, the humidifier will stop. When the humidity level drops below the set humidity, the humidifier will turn on automatically.
NOTE: When the SmartTouch™ Electronic Humidistat is set, either the HIGH or LOW power light and the percent
NOTE: It may take up to 60 minutes of operation for the FilterCheckTM Indicator to reflect the filter condition. New filters will register in the section reading Good filter. After frequent use of your humidifier, the FilterCheckTM Indicator will let you know when the filters need to be changed, see Figure 3.
Figure 3
grow in the water within the water tank. You must routinely follow the cleaning procedures that follow in order to ensure proper, efficient operation of your humidifier. Proper maintenance and cleaning is essential to the continued performance of your unit and the avoidance of algae or bacteria
If after having read this leaflet, you have any questions or comments on your humidifier,
call
127459/9100030005141
14.Humidifier should be unplugged when not in use.
15.NEVER tilt, move, or attempt to empty unit while it is operating. Shut off and unplug before removing the
The length of cord used on this appliance was selected to reduce the hazards of becoming tangled in, or tripping over a longer cord. If a longer cord is necessary an approved extension cord may be used. The electrical
2. When full, carry tank to the humidifier and place onto |
the base. The tank holds 3/4 gallons of water and the |
base holds 1/4 gallon of water. The tank will |
immediately begin to empty into base. |
humidity light will remain lit during operation. (See figure 2.)
NOTE: Allow up to 30 minutes for the filter to fully absorb water and for the unit to produce moisture.
When the needle is in the (CHANGE) section, this means the proper amount of moisture is not getting into your air due to the excessive minerals and sediment that have
DAILY MAINTENANCE:
STORAGE INSTRUCTIONS
Troubleshooting
FREQUENTLY ASKED QUESTIONS
6 YEAR LIMITED WARRANTY
How to Obtain Warranty Service
1.Before cleaning, push the SmartTouch™ button for 2 seconds to turn the unit OFF and disconnect from the electrical outlet.
2.Remove the housing and the tank from the humidifier and place in sink or tub.
3.Carry the base of the unit to the sink, remove the wick holder and wicks, place in sink, drain any remaining water and rinse thoroughly to remove any sediment or dirt. Wipe clean, and dry with a clean cloth or paper towel. NOTE: the base and wick holder are dishwasher safe TOP RACK ONLY.
4.Drain the water from the tank into the sink and rinse tank thoroughly. Wipe clean, and dry with a clean cloth or paper towel
5.Put filters back in wick holder, replace on base, replace the housing, then refill tank with cool tap water as instructed earlier in the Filling Instructions. Do not overfill.
6.Follow Operating Instructions.
WEEKLY MAINTENANCE:
To Remove Scale:
1.Repeat steps
2.Clean the base by partially filling the base with one
Cleanse CleanTM solution (Model S1710) by the manufacturer. Leave this solution in the base for 20 minutes, while cleaning the all interior surfaces with a soft brush. Remove base scale by wiping the base with a cloth dampened with undiluted white vinegar.
3.Rinse with clean warm water to remove the cleaning solution before disinfecting the tank.
To Disinfect Humidifier Base and Tank:
1.Fill humidifier base with 1/4 gallon of water and 1/2 teaspoon of chlorine bleach.
2.Fill the tank 1/2 full with water and 1/2 teaspoon of chlorine bleach.
3.Let the solution stand for 20 minutes, swishing every few minutes. Wet all surfaces.
4.Carefully empty the base and tank after 20 minutes, and rinse with water until you cannot detect any bleach smell. Dry with a clean cloth or paper towel.
5.Check the FilterCheckTM Indicator to see if it is time to replace the filters. Depending on water hardness in your area, it may be necessary to change the filters every
6.Refill the water tank as directed with cool tap water, replace the humidifier housing, and turn the unit on.
When not using your humidifier for an extended period of time:
1.Dispose of the filters. DO NOT leave in unit.
2.Clean, rinse and thoroughly dry the humidifier as directed in weekly maintenance. DO NOT leave any water in the unit when storing. Leaving water in the unit may render the unit inoperable for the following season.
3.Place the humidifier in the original carton and store in a cool, dry place.
4.Order your replacement filters for next year’s use.
REPLACEMENT ACCESSORIES:
To order the replacement accessories you can do any of the following:
•Visit your local retailer.
•Call consumer service at
If you have any questions regarding your product or would like to learn more about other Bionaire® products, please contact our Consumer Service Department at
Trouble
•Unit does not turn on.
•Mist output minimal to none.
•Water leaks from reservoir.
•Filter turns brown.
• Film on water reservoir.
•Water in reservoir appears cloudy.
•Unit cycles on/off.
•Very tight reservoir cap.
•FilterCheck™ is not working.
Probable Cause
☛Water spilled in humidistat.
☛Circuit breaker has been tripped.
☛Filter has not absorbed water.
☛Mineral buildup in tray.
☛Humidistat is set too low.
☛Filter needs to be replaced.
☛Rubber reservoir ring is missing or improperly placed.
☛Cap not tight enough.
☛The filter needs to be replaced.
☛Short filter life.
☛Mineral deposits cause film on reservoir to build up.
☛Filter needs to be replaced.
☛Water reservoir filled with warm water.
☛Humidifier is reacting to room.
☛Reservoir cap over tightened.
☛Takes 60 minutes to register.
Solution
✔Drain water from base and allow unit to dry for 30 minutes.
✔Check circuit breaker.
✔Wait 30 minutes before starting humidifier.
✔See Weekly Maintenance under Cleaning and Maintenance Instructions. Regular cleaning is recommended to keep the unit functioning properly.
✔Raise the level of humidity by adjusting the humidistat (see Operating Instructions).
✔Replace your filter (BWF100) by calling
✔Remove reservoir cap then replace or reposition ring.
✔Tighten the cap.
✔Replace your filter (BWF100) by calling
✔In areas with hard water the filter will need to be changed more frequently.
✔See Daily Maintenance under Cleaning and Maintenance instructions. Regular cleaning is recom mended to keep the unit functioning properly.To order Clean Away™ (DMS216), call
✔Replace your filter (BWF100) by calling
✔Use cool water to fill the water reservoir – and only use Bionaire® products recommended in this manual.
✔Set the digital Humidistat to a higher or lower desired setting.
✔Add liquid soap to cap gasket to ease opening.
✔Allow the humidifier to run continuously for 60 minutes for the FilterCheck™ Indicator to reflect the filter condition.
Question
•What are the variables that affect run time?
•How do I remove film on water tank?
•How can I extend the run time?
ANSWER
☛The estimated run time for this humidifier is based on average room conditions. The actual run time of your humidifier is dependent on numerous variables such as:
1.Air exchange in the room where the humidifier is placed.
2.Room construction where the humidifier is placed.
3.Temperature of the room where the humidifier is placed.
4.Humidity levels in the room where the humidifier is placed.
5.Movement of occupants and the opening and closing of doors in the room where the humidifier is placed.
6.Home furnishings in the room where the humidifier is placed.
☛See Daily Maintenance instructions. Regular cleaning is recommended.
☛Run your unit on the lowest setting.
☛If your unit has electronics, set it to your desired humidity level. The unit will turn on and off, which will extend the run time.
☛Fill the tank all the way full, place it on the base, let the water empty into the base until it stops bubbling, then refill the tank full again. This ensures maximum water capacity and will extend run time.
Sunbeam Products, Inc. doing business as Jarden Consumer Solutions or if in Canada, Sunbeam Corporation (Canada) Limited doing business as Jarden Consumer Solutions (collectively “JCS”) warrants that for a period of six years from the date of purchase, this product will be free from defects in material and workmanship. JCS, at its option, will repair or replace this product or any component of the product found to be defective during the warranty period. Replacement will be made with a new or remanufactured product or component. If the product is no longer available, replacement may be made with a similar product of equal or greater value. This is your exclusive warranty. Do NOT attempt to repair or adjust any electrical or mechanical functions on this product. Doing so will void this warranty.
This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep the original sales receipt. Proof of purchase is required to obtain warranty performance. JCS dealers, service centers, or retail stores selling JCS products do not have the right to alter, modify or any way change the terms and conditions of this warranty.
This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or misuse of the product, use on improper voltage or current, use contrary to the operating instructions, disassembly, repair or alteration by anyone other than JCS or an authorized JCS service center. Further, the warranty does not cover: Acts of God, such as fire, flood, hurricanes and tornadoes.
What are the limits on JCS’s Liability?
JCS shall not be liable for any incidental or consequential damages caused by the breach of any express, implied or statutory warranty or condition.
Except to the extent prohibited by applicable law, any implied warranty or condition of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty.
JCS disclaims all other warranties, conditions or representations, express, implied, statutory or otherwise.
JCS shall not be liable for any damages of any kind resulting from the purchase, use or misuse of, or inability to use the product including incidental, special, consequential or similar damages or loss of profits, or for any breach of contract, fundamental or otherwise, or for any claim brought against purchaser by any other party.
Some provinces, states or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from province to province, state to state or jurisdiction to jurisdiction.
In the U.S.A.
If you have any question regarding this warranty or would like to obtain warranty service, please call
In Canada
If you have any question regarding this warranty or would like to obtain warranty service, please call
In the U.S.A., this warranty is offered by Sunbeam Products, Inc. doing business Jarden Consumer Solutions located in Boca Raton, Florida 33431. In Canada, this warranty is offered by Sunbeam Corporation (Canada) Limited doing business as Jarden Consumer Solutions, located at 20 B Hereford Street, Brampton, Ontario L6Y 0M1. If you have any other problem or claim in connection with this product, please write our Consumer Service Department.
PLEASE DO NOT RETURN THIS PRODUCT TO ANY OF THESE ADDRESSES OR TO THE PLACE OF PURCHASE.
© 2008 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All Rights Reserved. Distributed by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions, Boca Raton, Florida 33431.
BCM7203/BCM7203RCCN08EFM1 | Printed in China |
