Bionaire BSF152T warranty Installation Instruction, Assembly Instructions, Operating Instructions

PLEASE READ AND SAVE THESE

IMPORTANT SAFETY INSTRUCTIONS

F E AT U R E S - O P E R AT I O N S

F E AT U R E S - O P E R AT I O N S

When using electrical appliances, basic safety precautions should always be taken including the following:

1.	Read all instructions before using this appliance.
2.	Use fan only for purposes described in the instruction
	manual.
3.	To protect against electrical shock do not immerse
	unit, plug or cord in water or spray with liquids. Plug
	the appliance directly into a 120V AC electrical outlet.
4.	Close supervision is necessary when any appliance is
	used by or near children.
5.	Unplug from outlet when not in use, when moving
	fan from one location to another, before putting on
	or taking off parts and before cleaning.

17.WARNING: To reduce the risk of electrical shock injury to persons, do not use in window.

18.WARNING: This fan is provided with an internal electronic fan speed control. To reduce the risk of fire or electric shock, do not use this fan with any other solid-state speed control device.

INSTALLATION INSTRUCTION

Figure 1

A	B	C	D	E	F	G	H
							P

PLEASE READ AND SAVE

THESE IMPORTANT

SAFETY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS

Assembly Time: 5-10 Minutes

NOTE: Check all packaging materials and make sure that you have all of the parts necessary for assembling your fan.

Figure 3

I

K

Figure 6

interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If the product does cause harmful interference to radio or television reception, which can be determined by turning the product on or off, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the product and the

receiver.

• Connect the product into an outlet on a circuit

different from that to which the receiver is

connected.

6.	Avoid contact with moving parts.
7.	Do not operate in the presence of explosive and/or
	flammable fumes.
8.	To avoid fire hazard, NEVER place the cord under
	rugs or any parts near an open flame, cooking or
	other heating appliance.
9.	Do not operate any appliance with a damaged cord
	or plug after the appliance malfunctions, or has been
	dropped/damaged in any manner. Discard fan or
	return to an authorized service facility for
	examination and/or repair.
10.	The use of attachments not recommended or sold by
	the appliance manufacturer may cause hazards.
11.	Do not use outdoors.
12.	Do not let the cord hang over the edge of a table,
	counter or come in contact with hot surfaces or leave
	exposed to high traffic areas.
13.	To disconnect, grip plug and pull from wall outlet.
	Never yank on cord.
14.	Always use on a dry, level surface.
15.	Do not operate fan until fully assembled with all
	parts properly in place.
16.	This product is intended for household use ONLY and
	not for commercial or industrial applications.

		Q
A.	Logo Plate	R
B.	Front Grill	I
C.	Fan Blade Cap
D.	Fan Blade
E.	Rear Grill Mounting Nut	K
F.	Rear Grill
G.	Motor Shaft
H.	Motor Housing	L
I.	Upper Pole

J.Grill Clips (6)

K.	Lower Pole	M
L.	Decorative Cap
M.	Base	N
N.	Base Weight
O.	Base Weight Nut	O
P.	Oscillation Control Knob
Q.	Tilt-Adjustment Knob
R.	Thumb Screw
S.	Mode/Off button
T.	IR Lens

1.Insert the threaded end of the Lower Pole into the Base. Refer to Figure 2.

2.Secure the Base Weight to the threaded end of the Lower Pole with the Base Weight Nut. Refer to Figure 2.

3.Insert the threaded end of the Upper Pole into the Lower Pole. Twist clockwise to lock. Refer to Figure 3.

4.Slide Neck of the Motor Housing over the Upper Pole and secure by tightening the Thumb Screw.

5.Secure the Rear Grill to the Motor Housing by tightening the Rear Grill Mounting Nut. Refer to Figure 4 for the correct positioning of the Rear Grill to the Motor Housing.

6.Secure the Fan Blade to the Motor Shaft by tightening the Fan Blade Cap. Refer to Figure 5.

7.Secure the Front Grill to the Rear Grill by snapping the Front Grill into the clips around the perimeter of the Rear Grill.

Figure 2

K

M

Figure 4

E

F

Figure 5

OPERATING INSTRUCTIONS

1.Set fan on a dry, level surface.

2.Plug cord into any standard 120 volt AC outlet.

3.The speed/mode is adjustable by pushing the Mode/

Off ( ) button either from the fan housing or the remote control.

OSCILLATION INSTRUCTIONS:

To turn the oscillation feature off pull the Oscillation

Control Knob ( ) all the way up. To turn the oscillation feature on push the Oscillation Control Knob

( ) all the way down.

FCC STATEMENT

Potential for Radio/Television interference

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.

• Consult the dealer or an experienced radio/TV

technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

REMOTE CONTROL

This unit includes two (2) AAA batteries.

Battery Replacement

a)Locate the battery cover on the back of the remote control handset. Slide the battery cover off with your thumb.

b)Use the tip of a pen to loosen each battery. Hold the remote control handset at an angle to allow the batteries to slide out.

c)Insert two new batteries, pressing them firmly into their slot.

d)Replace the battery cover.

NOTES:

• Do not mix old and new batteries.
•	Do not mix alkaline, standard (carbon-zinc), or
	rechargeable (nickel-cadmium) batteries.
•	Replace all batteries of a set at the same time.

THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet.

DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS

SAFETY FEATURE IN ANY WAY.

C D

These limits are designed to provide reasonable protection against harmful interference in a residential installation. The product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

• Clean the battery contacts and the devices’ contacts
	prior to installing the batteries.
•	Remove the batteries from the equipment when it is
	not being used for an extended period of time.
•	Remove the used batteries promptly.

BSF152T-U_08EM1.indd 2

12/22/08 3:49:39 PM