Black & Decker 244137-01 instruction manual Assembly / Adjustment SET-UP

G H 6 0 0 T r i m m e r / E d g e r

INSTRUCTION MANUAL

Date Code: Catalog Number: GH600

￿

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

1-800-54-HOW-TO (544￿ -6986)

IF YOU SHOULD EXPERIENCE A PROBLEM

WITH YOUR BLACK & DECKER PRODUCT,

CALL 1-800-54-HOW-TO (544-6986).

BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION

AVAILABLE, CATALOG NO., TYPE NO., AND DATE CODE.

IN MOST CASES, A BLACK & DECKER REPRESENTATIVE CAN RESOLVE

YOUR￿ PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR

COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.

KEY INFORMATION YOU SHOULD KNOW:

• The guard must be installed before trimming or edging - if not, the motor will

overheat.

• When replacing the line, use only .065” diameter ROUND line - otherwise the unit

will not function properly.

• Do not bump the feed head against the ground - it will disrupt the feed mechanism.

• Angle tool slightly (5° to 10°) when trimming.

•STAY ALERT – Watch what you are doing. Use common sense. Do not operate tool when you are tired.

•MAINTAIN APPLIANCES WITH CARE – Follow instructions in maintenance section. Inspect extension cords periodically and replace if damaged. Keep handles dry, clean and free from oil and grease.

•CHECK DAMAGED PARTS – Before further use of the appliance, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other condition that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this manual.

• WARNING: When servicing double insulated tools, USE ONLY IDENTICAL REPLACEMENT PARTS. Replace or repair damaged cords.

• WARNING: To prevent electrical shock hazard, use only with an extension cord suitable for outdoor use. Always connect extension cords to a fused line or one protected by a circuit breaker.

SAFETY WARNINGS AND INSTRUCTIONS: POLARIZED PLUGS

To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other) and will require the use of a polarized extension cord. The appliance plug will fit into a polarized extension cord only one way. If the plug does not fit fully into the extension cord, reverse the plug. If the plug still does not fit, obtain a correct polarized extension cord. A polarized extension cord will require the use of a polarized wall outlet. This plug will fit into the polarized wall outlet only one way. If the plug does not fit fully into the wall outlet, reverse the plug. If the plug still does not fit, contact a qualified electrician to install the proper wall outlet. Do not change the equipment plug, extension cord receptacle, or extension cord plug in any way.

SAFETY WARNINGS AND INSTRUCTIONS: EXTENSION CORDS

Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. If the extension will be used outside, the cord must be suitable for outdoor work. The letters “WA” on the cord jacket indicate that the cord is suitable for outdoor use.

Volts	Minimum Gage for Cord Sets
	Total Length of Cord in Feet			101-150
120V	0-25	26-50	51-100
240V	0-50	51-100	101-200	201-300

Ampere Rating				American Wire Gage
More		Not more
Than		Than
0	-	6	18	16	16	14
6	-	10	18	16	14	12
10-		12	16	16	14	12
12-		16	14	12	Not Recommended

• Always use the cord retainer and the extension cord lock feature.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

Cat No. GH600	Form No. 244137-01 Rev. 2	(NOV. ‘03)
Copyright © 2003 Black & Decker		Printed in Mexico

WARNING: IMPORTANT SAFETY WARNINGS AND INSTRUCTIONS

TO REDUCE RISK OF INJURY:

•Before any use, be sure everyone using this tool reads and understands all safety instructions and other information contained in this manual.

•Save these instructions and review frequently prior to use and in instructing others.

• CAUTION: Failure to comply with the recommendations outlined in the key information section will void warranty.

• WARNING: When using electric gardening appliances, basic safety precautions should always be followed to reduce risk of fire, electric shock, and personal injury, including the following:

• WARNING: Some dust created by this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

•compounds in fertilizers

•compounds in insecticides, herbicides and pesticides

•arsenic and chromium from chemically treated lumber

To reduce your exposure to these chemicals, wear approved safety equipment such as dust masks that are specially designed to filter out microscopic particles.

12

5

Cord Retainer￿

4Dispositif de retenue de la rallonge￿ Retén para el cable

3

6

Cord Lock Fork￿ Dispositif de verrouillage ￿ de la rallonge￿

Seguro para el cable￿

￿

5°-10°

• WARNING: This product contains chemicals, including lead, known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling.

• CAUTION: Wear appropriate personal hearing protection during use. Under some conditions and

duration of use, noise from this product may contribute to hearing loss.

READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE USING.

GENERAL SAFETY WARNINGS AND INSTRUCTIONS FOR ALL TOOLS

•ALWAYS WEAR EYE PROTECTION – Wear safety spectacles or goggles at all times when this tool is plugged in.

•GUARD – Do not use this tool without guard attached.

•DRESS PROPERLY – Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves and substantial rubber soled footwear are recommended when working outdoors. Don’t operate the tool when barefoot or wearing open sandals. Wear long pants to protect your legs. Wear protective hair covering to contain long hair.

•NYLON LINE – Keep face, hands and feet clear of rotating nylon line at all times.

•THE ROTATING LINE PERFORMS A CUTTING FUNCTION – Use care when trimming around screens and desirable plantings.

•KEEP ALL BY-STANDERS AWAY – at a safe distance from work area, especially children.

•IMPORTANT WARNING – When being used as an Edger, stones, pieces of metal and other objects can be thrown out at high speed by the line. The tool and guard are designed to reduce the danger. However, the following special precautions should be taken:

•MAKE SURE that other persons and pets are at least 100 feet away.

•TO REDUCE THE RISK of rebound (ricochet) injury, work going away from any nearby solid object such as wall, steps, large stone, tree, etc. Use great care when working close to solid objects and where necessary, do edging or trimming by hand.

•AVOID ACCIDENTALLY STARTING – Don’t carry plugged-in tool with finger on trigger.

•DO NOT FORCE THE TOOL – at a rate faster than the rate at which it is able to cut effectively.

•USE THE RIGHT TOOL – Do not use this tool for any job except that for which it is intended.

•DON’T OVERREACH – Keep proper footing and balance at all times.

•DON’T ABUSE CORD – Don’t yank cord from power supply. Keep cord from heat, oil, and sharp edges.

•DAMAGE TO UNIT – If you strike or become entangled with a foreign object, stop tool immediately, unplug, check for damage and have any damage repaired before further operation is attempted. Do not operate with a broken hub or spool.

•DAMAGE TO CORD – Keep power cord away from rotating line. If you damage the cord, unplug it from the power supply before moving the tool or examining the damage. A damaged cord must be replaced before further use.

•DISCONNECT TOOL – when not in use, when replacing line, or prior to cleaning.

•AVOID DANGEROUS ENVIRONMENTAL CONDITIONS – Do not use electric tools in damp or wet locations. Follow all instructions in this Instruction Manual for proper operation of your tool. Don’t use the tool in the rain.

•DO NOT OPERATE portable electric tools in gaseous or explosive atmospheres. Motors in these tools normally spark, and the sparks might ignite fumes.

•STORE IDLE TOOLS INDOORS – When not in use, tools should be stored indoors in a dry, locked-up place out of reach of children.

•GROUND FAULT CIRCUIT INTERRUPTER (GFCI) protection should be provided on the circuits or outlets to be used for the gardening appliance. Receptacles are available having built in GFCI protection and may be used for this measure of protection.

•SECURE EXTENSION CORD using the cord retainer shown in Figure 4.

7 8 9

Conversion Button￿

Bouton de conversion￿

Botón de conversión

Air Intake Slots￿

Fentes d'admission d'air￿

Tomas de aire

10 11 12

13 14 15

ASSEMBLY / ADJUSTMENT SET-UP

• WARNING: The guard must always be on the tool to protect the user.

NEVER OPERATE TOOL WITHOUT GUARD FIRMLY IN PLACE.

UNPLUG THE TOOL BEFORE ATTEMPTING TO ATTACH THE GUARD.

1.Position the open center of the guard over the line feed head (Figure 1).

2.Hinge the guard on the hook located on the lower motor housing. Ensure the line is free, and not tucked under the guard. Once hooked, lightly pull on the back edge of the guard and push the guard down until the 3 latches snap into place on the motor housing. (Figure 2)