BDWF7710Pub1000001430 10/11/04 4:51 PM Page 4
Product may vary slightly from what is illustrated.
11
How to Use
This appliance is for household use.
IMPORTANT: During the first few minutes of initial use, a slight odor may be noticeable. This is normal and will quickly disappear.
INSTALLATION INSTRUCTIONS
1.Unpack twin window fan carefully.
2.This unit is designed for use in
3.This fan is designed to be used (and recommended for use) with a screen in the window.
4.With the sliding portion of the window fully open, take an accurate inside measurement (left to right for
For double-hung type windows
1. | With the window fully open, set the fan in the window with front of fan facing the |
| INSIDE. |
2. | Hold fan with one hand while attaching/adjusting panels with the other. Attach one of |
| the panel inserts by sliding it down the groove located at the top left of fan. Before |
| closing window, pull open clamps located at top and bottom on right side on fan, and |
† 1. Panel insert
(2 panel inserts per set Part #103409900592)
2.Groove
3.Digital control panel
4.Carry handle
5.Release clamp
6.Expandable panel
7.Twin motors
8.7" (18cm) reversible blades
9.Remote control storage
†10. Remote control
(Part #103530000021)
† 11. Optional feet
(2 optional feet per set, right Part #103409900583, left Part # 103409900584)
12.10' cord (25 cm)(not shown)
13.Screws (not shown)
†Consumer replaceable
| adjust expandable panel, if necessary. |
3. | Close the window on top of the fan with the bottom edge of the window behind the lip |
| of fan housing. |
4. | If the fan still does not fit properly in the window, readjust the expandable panel on |
| right side of fan to fill in remaining space between panel and window frame until a |
| secure fit is achieved. |
For vertical slider-type windows
1. | Position the fan in the window with the power switch facing the center of the opening. |
2. | To adjust height, remove fan from window. If additional height required is 4" (10 cm) |
| or less, extend the expandable panel until it matches the height of the window. (For |
| example, if window height is 28" (71 cm), adjust panel so that the height of the fan is |
| also 28" (71 cm)). If fan height required is more than 28" (71 cm), attach one or both of |
1.
2. Reverse buttons
3. Digital temperature display
4. Rainsafe™ button
5. Remote control sensor
6. Adjustable thermostat buttons
7. Temperature control button
B |
A |
3 |
| the insert panels, as described in #2 of FOR |
| above. |
3. | With the window fully open, position the fan in the window with the expandable panel |
| at the top and with power switch facing the center of the opening. |
4. | Fan must fit securely against the inside edge of the window opening. |
5. | Slide the sliding window to meet the edge of the fan. The side edge of the window must |
| fit securely behind the lip of fan housing. |
6. | Adjust the expandable panel to fill in remaining space between fan and window frame. |
Expandable panel locks into position by closing the clamps once fit is established. | |
OPERATING INSTRUCTIONS | |
1. | Plug into 120V AC electric outlet. |
2.On/Off/SPEED— Press speed button to turn the fan on. Fan default direction when the unit is turned on is intake. Fan begins blowing at LOW speed, the corresponding LED speed indicator illuminates. To turn the fan off press the speed button through the cycle (LOW, MED, HI) until all speed lights are off.
3.Intake/Exhaust/Exchange — Both fans are automatically reversible and operate independently in either an intake or exhaust mode. The IN/OUT directional LED illuminates green for intake and red for exhaust.
To pull in fresh air from the outside – push reverse button to IN (green).
To remove stale or smoky air from the room - push reverse button to OUT (red). For air exchange
4