Black & Decker DE791B manual Setting the CLOCK/TIMER and AUTO-BREW Clock/Timer, Auto-Brew

How to Use

This appliance is intended for household use only.

GETTING STARTED

1.Remove all stickers and packing materials attached to the coffeemaker.

2.Wash all parts as instructed in the “Care and Cleaning”section.

Note: Coffeemaker works without having to set the clock.

3.Before using your coffeemaker for the first time, brew water through it as instructed in the “BREWING” section without adding grounded coffee.

4.Once brewing is complete the coffeemaker and the brewing indicator light automatically shut off.

5.Discard the water from the thermal carafe and rinse it.

Important: Do not place the thermal carafe on or near a gas or electric burner, in a heated oven or in a microwave oven. Avoid rough handling and sharp blows.

BREWING

E

F

1.This feature enables you to pour a cup of coffee while the coffee is brewing before the brewing cycle is complete.

2.To pour coffee, align the arrow on the brew-thru lid with the “Pour” arrow on the handle of the thermal carafe by turning the lid counterclockwise (E).

Note: Make sure the brew-thru lid is secure before you pour the coffee.

3.When you are finished pouring the coffee, turn the brew-thru lid clockwise until it is in the “Close” position (F).

4.Immediately replace the thermal carafe back on the carafe plate so that brewing can continue.

Important: To avoid possible overflow after removing the carafe, be sure to replace the carafe under the brew basket within 30 seconds to prevent the basket from overflowing.

1.To fill the water reservoir, lift the cover and fill it with water up to your desired level. Note: Maximum capacity is 8-cups of water. Do not overfill.

2.Place a filter into the brew basket. Fill the filter with the desired amount of coffee.

SETTING THE CLOCK/TIMER AND AUTO-BREW Clock/Timer

1. Plug in unit, the clock flashes 12:00 a.m. until time is set.

B

C

Note: We recommend 1-2 tablespoons (5-10 grams) of grounded coffee for every 6 oz. (180ml.) of water. If brewed coffee is too strong for your taste just add a little bit of hot water to your cup of brewed coffee.

3.To insert brew-thru lid into thermal carafe, align the brew-thru lid arrow with the “Insert and Align” arrow on the thermal carafe and twist clockwise (B).

4.Turn the brew-thru lid clockwise until it is in the “Close” position to brew your coffee (C).

Note: Coffee may overflow if the brew-thru lid is not properly in place.

5.Place the thermal carafe on the carafe plate and plug in the unit.

6.Press the “ON” button to start the brewing cycle. Once the brewing indicator light lights up, the brewing cycle begins.

Note: For delay brewing, see “Setting the Clock/Timer & Auto-Brew.”

2.	To set current time of day: Press the “HOUR” button until the digital display shows
	the correct hour.
3.	The light on the top left hand corner of the digital display indicates “P.M.” time.
4.	Then press the “MIN” button until the display shows the correct minutes.
5.	Once the time is set, the clock continues to keep time unless coffeemaker is unplugged
	or a power failure occurs.
6.	To reset the time again follow steps 1-4.

Auto-Brew

1.Press the “PROG” button and the auto brew indicator light on the upper right hand corner of the digital display starts flashing, indicating it is being programmed.

2.Press the “HOUR”, then the “MIN” button until the digital display shows the correct time.

Note: Make sure the “P.M.” indicator light on the top left hand corner of the digital display is off if you would like your coffee to be brewed in the morning.

3.Then press the “AUTO” button and the auto brew indicator light on the upper right hand corner of the digital display lights up (see fig. A)

Note: If you take too long to press the correct hour and minutes after you have pressed the “PROG” button, the clock will return to the time setting. To program auto-brew again just follow steps 1-3.

7.Once the brewing cycle is complete the coffeemaker and the brewing indicator light automatically shut off.

8.Remove the thermal carafe from the carafe plate.

4.	When the brewing cycle begins the auto brew indicator light turns off and the
	brewing indicator light turns on.
5.	When the brewing cycle is complete the coffeemaker and the brewing indicator light

D

9.To pour coffee, align the arrow on the brew-thru lid with the “Pour” arrow on the handle of the thermal carafe by turning the lid counterclockwise (D).

Note: Make sure the brew-thru lid is secure before you pour the coffee.

10.Proceed to serve the coffee.

11.Once you finish serving the coffee, close the lid again by turning it clockwise.

12.Put the thermal carafe back on the carafe plate.

automatically shut off.

Note: The thermal carafe will keep your coffee hot.

6.	To check your pre-set auto time, press the “PROG” button and the auto brewing time
	will display.
7.	When the clock returns to the current time, press “AUTO” button to reactivate
	the timer.
8.	The auto-brew indicator light on the upper right hand corner of the digital display
	lights up (see fig. A)
9.	To automatically brew coffee again at the same pre-set auto-brew time, prepare

Note: The thermal carafe keeps the coffee hot. Make sure the brew-thru lid is always in the close position after every use. This allows the coffee to stay hot longer.

Sneak-A-Cup®Interrupt Feature

11

coffeemaker for brewing and press the “AUTO” button.

10. If you want to change the time of the auto-brew just follow steps 1-3.

12