Safety Warnings and Instructions: Charging the Drill
1.This manual contains important safety and operating instructions.
2.Before using battery charger, read all instructions and cautionary markings on (1) bat- tery charger, (2) battery, and (3) product using battery.
3.
CAUTION: To reduce the risk of injury, charge only Black & Decker Battery Packs. Other types of batteries may burst causing personal injury and damage.
4.Do not expose charger to rain or snow.
5.Use of an attachment not recommended or sold by Black & Decker may result in a risk of fire, electric shock, or injury to persons.
6.To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting charger.
7.Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.
8.An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire, electric shock or electrocution.
a.
b.An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety, and to prevent loss of power and overheating. The smaller the gauge number of the wire, the greater the capacity of the cable; that is, 16 gauge has more capacity than 18 gauge. When using more than one extension to make up the total length, be sure each extension contains at least the minimum wire size.
CHART FOR MINIMUM WIRE SIZE (AWG)OF EXTENSION CORDS
NAMEPLATE RATING AMPS – 0 – 10.0 |
| |||||
Total Extension Cord Length (ft) | 25 | 50 | 75 | 100 | 125 | 150 |
Wire Gauge | 18 | 18 | 16 | 16 | 14 | 14 |
9.Use only the supplied charger when charging your drill. The use of any other charger could damage the drill or create a hazardous condition.
10.Use only one charger when charging.
11.Do not attempt to open the charger or the drill. There are no customer serviceable parts inside. Return to any authorized Black & Decker service center.
12.DO NOT incinerate the drill or battery packs even if they are severely damaged or com- pletely worn out. The batteries can explode in a fire.
13.A small leakage of liquid from the battery cells may occur under extreme usage, charg- ing or temperature conditions. This does not indicate a failure. However, if the outer seal is broken and this leakage gets on your skin:
a.Wash quickly with soap and water.
b.Neutralize with a mild acid such as lemon juice or vinegar.
c.If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10 minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is a 25- 35% solution of potassium hydroxide.
Charging the Battery Pack
THE BATTERY PACK IS NOT FULLY CHARGED AT THE FACTORY. BEFORE ATTEMPTING TO CHARGE THE BATTERY PACK, THOROUGHLY READ ALL OF THE SAFETY INSTRUCTIONS.
The charger is designed to use standard household 120 volt 60 Hz power.
1.Plug the charger into any standard 120 Volt 60 Hz electrical outlet. NOTE: Do not charge by means of an engine generator or DC power source. Use only 120V AC.
2.Slide the charger onto the battery pack as shown in Figure 1 and let the battery charge initially for 9 hours. After the initial charge, under normal usage, your battery pack should be fully charged in 3 to 6 hours.
3.Unplug charger, and remove the battery pack. Place the battery in the tool and be certain that it is inserted fully into the tool cavity until it “clicks” into place.
NOTE: To remove the battery from the drill, press down on the release button on the back of the battery (Figure 2) and slide out.
Important Charging Notes
1.After normal usage, your battery pack should be fully charged in 3 to 6 hours. If the bat- tery pack is
2.DO NOT charge the battery pack in an air temperature below 40°F (4,5 °C) or above 105°F.(40,5 °C) This is important and will prevent serious damage to the battery pack. Longest life and best performance can be obtained if battery pack is charged when air temperature is about 75°F.(24°C).
3.While charging, the charger may hum and become warm to touch. This is a normal con- dition and does not indicate a problem.
4.If the battery pack does not charge
5.The battery pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE using product with its battery pack in a depleted condition.
6.To prolong battery pack life, avoid leaving the battery pack on charge for extended periods of time (over 30 days without use). Although overcharging is not a safety concern, it can significantly reduce overall battery pack life.
7.The battery pack will reach optimum performance after being cycled 5 times during normal usage. There is no need to run the batteries down completely before recharging. Normal usage is the best method of discharging and recharging the batteries.
Safety Warnings and Instructions: Drills
1.As shown in figure 3, use side handle and always hold drill firmly to control its twisting action. Make sure that the side handle is securely attached and hand tightened to the orange housing surface directly behind the torque adjust collar.
2.When attaching accessories in the drill chuck, hand tighten the keyless chuck firmly.
WARNING: Drill may stall (if overloaded or improperly used) causing a twist. Always expect the stall. Grip the drill firmly to control the twisting action (see Fig. 3) and prevent loss of control which could cause personal injury. If a stall does occur, release the trigger immediately and determine the reason for the stall before
Operating Instructions
Trigger Switch & Reversing Button - Figure 4
The drill is turned ON and OFF by pulling and releasing the trigger switch shown in Figure 4. The farther the trigger is depressed, the higher the speed of the drill. A forward/reverse control button determines the direction of the tool and also serves as a lock off button. To select forward rotation, release the trigger switch and depress the forward/reverse control button as depicted in figure 4. To select reverse, depress the forward/reverse control button the opposite direction. The center position of the control button locks the tool in the off position. When changing the position of the control button, be sure the trigger is released.
Torque Control - Figure 5
This tool is fitted with a collar to select the operating mode and to set the torque for tightening screws. Large screws and hard workpiece materials require a higher torque setting than small screws and soft workpiece materials.
•For drilling in wood, metal and plastics, set the collar to the drilling position symbol 
.
•For screwdriving, set the collar to the desired setting. If you do not yet know the appropriate setting, proceed as follows:
•Set the collar to the lowest torque setting.
•Tighten the first screw.
•If the clutch ratchets before the desired result is achieved, increase the collar setting and continue tightening the screw. Repeat until you reach the correct setting. Use this setting for the remaining screws.
Hammer Action – Figure 6
Your drill has hammer action which is engaged by shifting the hammer/drill button on the top of the unit. To select hammering, turn off the drill and shift the hammer/drill button back (away from the chuck) to the hammer symbol. To select drilling, turn off the drill and shift the hammer/drill button forward towards the chuck.
Keyless Chuck
To insert a drill bit or other accessory:
1.Grasp the rear half of the chuck with one hand and use your other hand to rotate the front half in the counterclockwise direction, as viewed from the chuck end.
2.Insert the bit or other accessory fully into the chuck, and tighten securely by holding the rear half of the chuck and rotating the front portion in the clockwise direction as viewed from the chuck end.
WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the front part of the chuck and turning the tool on. Damage to the chuck and personal injury may occur when changing accessories.
Screw Driving
For driving fasteners, the reversing button should be pushed to the left. Use reverse (button pushed to the right) for removing fasteners. When moving from forward to reverse, or vice versa, always release the trigger switch first.
Drilling
•Use sharp drill bits only.
•Support and secure work properly, as instructed in the Safety Instructions.
•Use appropriate and required safety equipment, as instructed in the Safety Instructions.
•Secure and maintain work area, as instructed in the Safety Instructions.
•Run the drill very slowly, using light pressure, until the hole is started enough to keep the drill bit from slipping out of it.
•Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but not so much as to stall the motor or deflect the bit.
•Hold the drill firmly with two hands to control its twisting action.
•DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE TO THE DRILL CAN RESULT.
•Minimize stalling on breakthrough by reducing pressure and slowly drilling through the last part of the hole.
•Keep the motor running while pulling the bit out of a drilled hole. This will help reduce jamming.
•Make sure switch turns drill on and off.
WARNING: It is important to support the work properly and to hold the drill firmly to prevent loss of control which could cause personal injury. If you have any questions on how to properly operate tool, call:
Drilling In Wood
Holes in wood can be made with the same twist drill bits used for metal or with spade bits. These bits should be sharp and should be pulled out frequently when drilling to clear chips from the flutes.
Drilling In Metal
Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be drilled dry. The cutting lubricants that work best are sulfurized cutting oil or lard oil.
Drilling in Masonry
Select position 2 for drilling with hammer action. Use carbide tipped masonry bits. Refer to Drilling section. Keep even force on the drill but not so much that you crack the brittle material. A smooth, even flow of dust indicates the proper drilling rate.
Maintenance
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authorized service centers or other qualified service personnel, always using identical replacement
parts.
The RBRC™ Seal The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the
paid by Black & Decker. In some areas, it is illegal to place spent
RBRC in cooperation with Black & Decker and other battery users, has established programs in the United States and Canada to facilitate the collection of spent nickel- cadmium batteries. Help protect our environment and conserve natural resources by returning the spent
Accessories
Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call:
WARNING: The use of any accessory not recommended for use with this tool could be hazardous.
The following accessories should be used only in the sizes specified below:
BITS, METAL DRILLING – Up to 1/2"(12.7mm); BITS, MASONRY DRILLING – Up to 1/2"(12.7mm); WOOD DRILLING – Up to
Service Information
All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under
Full Two-Year Home Use Warranty
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required. Black & Decker owned and authorized Service Centers are listed under "Tools- Electric" in the yellow pages of the phone directory and on our website www.blackanddecker.com.
This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state or province to province. Should you have any questions, contact the manager of your nearest Black & Decker Service Center. This product is not intended for commercial use.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call
Special WARRANTY Note to Contractors:
FIRESTORMTM branded products are offered as high end consumer home use tools and carry a HOME USE WARRANTY. These tools are designed, manufactured and tested to meet or exceed the needs of the
UNDER OUR WARRANTY.
Imported by |
| See | |
Black & Decker (U.S.) Inc., |
| ||
701 | E. Joppa Rd. |
| – Yellow Pages – |
Towson, | MD 21286 U.S.A. |
| for Service & Sales |
