Black & Decker GLC1423L, GLC1825L manual Use, Hints for optimum use

ENGLISH (Original instructions)

Use

Warning! Let the tool work at its own pace. Do not overload.

Charging the battery (fig. G)

The battery needs to be charged before first use and whenever it fails to produce sufficient power on jobs that were easily done before. The battery may become warm while charging; this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures below 10 °C or above 40 °C. Recommended charging temperature: approx. 24 °C.

Note: The charger will not charge a battery if the cell temperature is below approximately 10 °C or above 40 °C. The battery should be left in the charger and the charger will begin to charge automatically when the cell temperature warms up or cools down.

uTo charge the battery (4), insert it into the charger (19). The battery will only fit into the charger in one way. Do not force. Be sure that the battery is fully seated in the charger.

uPlug in the charger and switch on at the mains.

The charging indicator (20) will blink.

The charge is complete when the charging indicator (20) switches to continuously on. The charger and the battery can be left connected indefinitely. The LED will switch on as the charger occasionally tops up the battery charge.

uCharge discharged batteries within 1 week. Battery life will be greatly diminished if stored in a discharged state.

Leaving the battery in the charger

The charger and battery pack can be left connected with the LED glowing indefinitely. The charger will keep the battery pack fresh and fully charged.

Setting the tool to trimming or edging mode (fig. H - J)

The tool can be used in trimming mode as shown in fig. E or in edging mode to trim overhanging grass along lawn edges and flower beds as shown in fig. F.

Trimming mode (fig. H)

For trimming, the trimmer head should be in the position shown in fig. H. If it is not:

uDisconnect the tool from the supply.

uLoosen the adjustment collar (6) by turning it clockwise.

uWhilst holding the handle (2), rotate the head (8) clockwise.

uTighten the collar (6) by turning it anti-clockwise.

uSlide the edge guide (9) into the motor housing.

Note: Note: The head will only rotate in one direction.

Edging mode (fig. I & J)

For edging, the trimmer head should be in the position shown in fig. I. If it is not:

uDisconnect the tool from the supply.

uLoosen the adjustment collar (6) by turning it clockwise.

uWhilst holding the handle (2), rotate the head (8) anti-clockwise.

uTighten the collar (6) by turning it anti-clockwise.

uSlide the edge guide out of the motor housing. Ensure that the edging guide (9) is fully extended, an audible click will be heard.

Note: The head will only rotate in one direction.

Switching on and off

uTo switch the tool on, press in and hold the lock off button

(3) then squeeze the trigger lever (1). Once the tool is running you may release the lock off button (3).

uTo switch the tool off, release the trigger lever.

Warning! Never attempt to lock the trigger lever in the on position.

Hints for optimum use

General

uIn order to achieve optimum cutting results, only cut dry grass.

Trimming

uHold the tool as shown in fig. K.

uGently swing the trimmer from side to side.

uWhen cutting long grass, work in stages from the top. Take small cuts.

uKeep the tool away from hard objects and delicate plants.

uCutting line will wear faster and require more feeding if the cutting is done along pavements or other abrasive surfaces or heavier weeds are being cut.

uIf the tool starts running slowly, reduce the load.

Edging

Optimum cutting results are achieved on edges deeper than 50 mm.

uDo not use the tool to create edges. To create edges, use an edging spade.

uGuide the tool as shown in fig. L.

uTo make a closer cut, slightly tilt the tool.

Fitting a new spool of cutting line (fig. M)

Replacement spools of cutting line are available from your Black & Decker dealer (cat. no. A6441). Complete cassettes containing a spool of cutting line are also available (cat. no. A6442).

8