For your convenience and safety, the following labels are on the laser.

Pour plus de commodité et de sécurité, les étiquettes suivantes sont apposées sur le laser. Para su comodidad y seguridad, el láser incluye las siguientes etiquetas.

588808-01Made in China

Type 1 3V DC

Use with compatible

LISTED

406A 1-800-54-HOW-TO

B&D Jig Saws.

Black & Decker (U.S.) Inc.,

Pats. Pend.

Towson, MD 21286 U.S.A.

WARNING/ADVERTENCIA/AVERTISSEMENT

 

COMPLIES

To reduce the risk of injury,

Para reducir el riesgo de

 

 

WITH 21CFR

user must read and

lesiones, el usuario debe

PARTS 1040.10

AND

understand instruction ON/OFF

leer y entender el

1040.11

EXCEPT FOR

 

manual. Use (2) AAA

manual de

DEVIATIONS PURSUANT

size alkaline batteries.

instrucciones.

TO LASER NOTICE NO.50,

DATED JULY 26,2001.

À titre préventif,

Utilice (2) baterías

 

 

 

lire le guide.

alcalinas AAA.

 

 

 

K

A

7

15

4

C

E

 

 

11

10

11

G

 

6

max

 

Hc

 

Ic

B

D

F

 

Ha

 

Ia

 

Hb

 

6

max

 

Ib

 

6

max

 

J

Screw

 

Vis

 

Tornillo

OFF

 

 

ON

Laser On/Off Button

Bouton marche/arrêt du laser

Botón de encendido/apagado del láser

Motor

Be sure your power supply agrees with nameplate marking. 120 Volts AC only means your tool will operate on standard 60 Hz household power. Do not operate AC tools on DC. A rating of 120 volts AC/DC means that you tool will operate on standard 60 Hz AC or DC power. This information is printed on the nameplate. Lower voltage will cause loss of power and can result in over-heating. All Black & Decker tools are factory-tested; if this tool does not operate, check the power supply.

SAVE THESE INSTRUCTIONS

Assembly

WARNING: Sharp blade. To prevent accidental operation, turn off and unplug saw before performing the following operations. Failure to do this could result in serious personal injury.

Fitting the saw blade (fig. A)

-Hold the saw blade (7) as shown, with teeth facing forward.

-Push the lever (4) downwards.

-Insert the shank of the saw blade into the blade holder (15) as far as it will go.

-Release the lever.

-Adjust the blade support roller as described below.

AccuCutTM blade support roller (fig. B)

After fitting the blade, you need to adjust the blade support roller (5).

Screwdriver Method

-Turn the slotted blade support adjustment screw (6) in direction A.

-Slide the blade support roller against the rear of the blade. The blade must locate in the central recess of the roller.

-Turn the blade support adjustment screw in direction B to lock the blade support in place.

Tool Free Method

-The blade support roller can be adjusted in a “tool free” manner, by turning the scrolling knob (8) so that the adjustment screw is rotated around to the front of the unit where it can be turned by hand.

Connecting a vacuum cleaner to the tool (fig. C & D)

-Align the dust extraction adaptor (14) with the saw shoe as shown.

-Insert the ribs (16) into the slots (17).

-Pull the adaptor towards the rear of the jigsaw to secure.

-Connect the vacuum cleaner hose (18) (not supplied) to the adaptor.

-Dust extraction is not possible when making bevel cuts.

WARNING: Fire Hazard. Do not use vacuum adapter when cutting metal. Metal filings will be hot and could cause a fire in the vacuum container.

Operating the Jig Saw

WARNING: Laceration Hazard. To prevent loss of control, never use the tool when the saw shoe is loose or removed. Failure to do this could result in serious personal injury.

Adjusting the shoe plate for bevel cuts (fig. E)

The shoe plate can be set to a left or right bevel angle of up to 45°.

-Turn the locking knob (11) in direction A to release the shoe plate (10).

-Pull the shoe plate (10) backwards and set it to the required angle. You can use the scale or a protractor to check the angle.

-Turn the locking knob (11) in direction B to lock the shoe plate in place.

To reset the shoe plate for straight cuts:

-Turn the locking knob (11) in direction A to release the shoe plate (10).

-Pull the shoe plate backwards and set it to an angle of approximately 0.

-Push the shoe plate forward.

-Turn the locking knob (11) in direction B to lock the shoe plate in place. Make sure that the shoe plate is supported by the guide ribs.

Variable speed control

-Set the variable speed control knob (3) to the required speed range. Use a high speed for wood, medium speed for aluminum and PVC and low speed for metals other than aluminum.

Switching On and Off

-To switch the tool on, press the on/off switch (1).

-For continuous operation, press the lock-on button (2) and release the on/off switch.

-To switch the tool off, release the on/off switch. To switch the tool off, when in continuous operation, press the on/off switch once more and release it.

Using the mode selector

The mode selector (9) can set in 3 positions

1.Scrolling position (figs F and G) - this position allows the scroller knob (8) to be rotated for intricate and accurate sawing. (In this position there is no orbital action.) It is recommended to use scroller blades when in this mode.

2.Straight cutting position (figs Ha, Hb and Hc ) this position turns off orbital action and locks the scroller knob to prevent its rotation. The scroller knob can be locked in any of 4 positions for straight cutting.

Method of engagement:

a.Turn the Mode Selector to the scrolling position.

b.Rotate the scroller knob to the desired position (this can be any of 4 positions - the blade can point forwards, reverse, left or right).

c.Turn the Mode Selector to the neutral position. (In this position the Scroller Knob cannot be turned).

3.Orbital Action Position (figs Ia, Ib and Ic) - this position switches on the orbital action for fast and efficient straight cuts. This mode can only be selected with the blade pointing forwards.

Method of engagement:

a. Turn the mode selector to the scrolling position.

b. Rotate the scroller knob to point the blade forwards.

c. Turn the Mode Selector to the orbital position. (In this position the Scroller Knob cannot be turned).

Operating the Laser

Installing the batteries

Detach the laser from the jig saw by removing the screw shown in figure J and pulling laser forward. Insert 2 fresh 1.5 volt AAA alkaline batteries making sure to match (+) and (-) terminals correctly. Reattach the laser.

WARNING: Batteries can explode, or leak, and can cause injury or fire. To reduce this risk:

Carefully follow all instructions and warnings on the battery label and package. • Always insert batteries correctly with regard to polarity (+ and -), marked on the battery and the equipment. • Do not short battery terminals. • Do not charge batteries. • Do not mix old and new batteries. Replace all of them at the same time with new batteries of the same brand and type. • Remove dead batteries immediately and dispose of per local codes. • Do not dispose of batteries in fire. • Keep batteries out of reach of children. • Remove bat- teries if the device will not be used for several months.

Page 2
Image 2
Black & Decker JS700L, 490525-00 instruction manual Assembly, Operating the Jig Saw, Operating the Laser

490525-00, JS700L specifications

The Black & Decker JS700L is a versatile jigsaw designed for both hobbyists and professional craftsmen who value precision and ease of use in their woodworking projects. This powerful tool combines cutting-edge technology with user-friendly features, making it a popular choice for various applications.

One of the standout features of the JS700L is its robust 5.0 amp motor, which provides ample power for cutting through a wide range of materials, including wood, metal, and plastic. The jigsaw’s variable speed control allows users to adjust the cutting speed from 0 to 3,000 strokes per minute, enabling precise cuts tailored to the specific material being worked on. This feature is particularly useful for intricate designs, curves, and complex shapes.

The JS700L incorporates a keyless blade change system, which simplifies the process of swapping out blades. This technology allows for quicker and more efficient blade changes, so users can spend less time preparing their tools and more time focusing on their projects. The jigsaw is compatible with a variety of blade types, providing flexibility depending on the cutting requirements.

Another significant characteristic of the JS700L is its unique orbital action feature. This technology enhances the cutting efficiency by changing the up-and-down motion of the blade to an orbital motion. This means that the blade not only moves vertically but also slightly forwards and backwards to increase the cutting stroke. As a result, users can achieve faster and smoother cuts, particularly in hardwoods.

For user comfort, the JS700L features a soft-grip handle that promotes a secure and comfortable grip during extended use. This ergonomic design reduces hand fatigue, allowing for prolonged work sessions without discomfort. Furthermore, the built-in dust blower keeps the cutting line clear of debris, ensuring improved visibility and accuracy for intricate cuts.

Safety is also a priority in the design of the JS700L. The jigsaw includes a safety switch that helps prevent accidental starts, providing peace of mind to users while operating the tool.

In summary, the Black & Decker JS700L is a well-rounded jigsaw that boasts a 5.0 amp motor, variable speed control, keyless blade changes, orbital action technology, and a user-focused design. With its combination of power, precision, and ease of use, it stands out as an indispensable tool for anyone looking to tackle a variety of cutting tasks with confidence.