90564630 li4000
work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA
approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.
WARNING: ALWAYS use safety glasses. Everyday eye glasses are NOT safety glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:
•ANSI Z87.1 eye protection (CAN/CSA Z94.3)
•ANSI S12.6 (S3.19) hearing protection
•NIOSH/OSHA/MSHA respiratory protection
SAFETY GUIDELINES - DEFINITIONS
It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.
SYMBOLS
FUNCTIONAL
DESCRIPTION
1)SWITCH
2)FORWARD / REVERSE / LOCK OFF SLIDER
3)FORWARD / REVERSE WINDOW
4)6 POSITION CLUTCH COLLAR
5)LED WORK LIGHT
6)HEX SPINDLE
7)SCREW HOLDER
8)CHARGING CONTACTS
9)CHARGING INDICATOR
10)CHARGING CRADLE
|
| 3 |
|
|
| 2 | 1 |
|
|
| |
| 4 |
| 8 |
5 |
|
|
|
6 | 7 |
|
|
|
| 9 | |
|
| 10 | |
|
|
|
The label on your tool may include the following symbols. |
|
|
| ||||
V | volts |
| A | amperes | A | ||
Hz | hertz |
| W | watts |
| ||
min | minutes |
| ...................... | alternating |
| ||
|
|
|
| no | current |
| |
...................... | direct current |
| no load speed |
| |||
.......................... | Class II Construction | ........................ | earthing terminal |
| |||
........................ | safety alert symbol | .../min | revolutions or |
| |||
|
|
|
|
|
| reciprocations |
|
|
|
|
|
|
| per minute |
|
• When using an extension cord, be sure to use one heavy enough to carry the current |
| ||||||
your product will draw. An undersized cord will cause a drop in line voltage resulting in |
| ||||||
loss of power and overheating. The following table shows the correct size to use |
| ||||||
depending on cord length and nameplate ampere rating. If in doubt, use the next |
| ||||||
heavier gage. The smaller the gage number, the heavier the cord. |
|
| |||||
| Recommended Minimum Wire Size for Extension Cords |
| |||||
Total Length of Cord |
|
|
|
|
| ||
25 ft. | 50 ft. | 75 ft. | 100 ft. | 125 ft. | 150 ft. | 175 ft. |
|
7.6 m | 15.2 m | 22.9 m | 30.5 m | 38.1 m | 45.7 m | 53.3 m |
|
Wire Size AWG |
|
|
|
|
|
| |
18 | 18 | 16 | 16 | 14 | 14 | 12 |
|
B |
4 | 5 | ||
|
|
|
|
|
|
|
|
|
|
|
|
