Blaupunkt SILVERSTONE C34 manual General Operations

General Operations

Turning the power On

Press the PWR button to turn the unit On.

Turning the power Off

Press the PWR button for more than 2 seconds. Display will revert to clock indication.

Tip

When you turn on the unit, “HELLO” will be displayed then “WELCOME” will momentarily be displayed before actual power on.

When you turn off the unit, “SEE YOU” will be displayed then “GOOD-BYE” will momentarily be displayed before actual power off.

You can edit these messages. (See “Turn on/off message edit”).

Volume Control

Rotate the VOL dial to adjust the volume.

Volume down Volume up

Muting the sound

Press PWR . The R-ch/L-ch Level Meter flashes.

To restore the previous volume level, press PWR again. Mute level can be adjustable. (See “Adjusting the Sound Characteristics”)

Switching the Display

Press the MENU to display the temporary indication (initial setting is clock display) for few seconds. Then automatically returns to the previous indication.

• Radio mode	• AUX mode
Frequency or Clock.	AUX title or Clock.
• Tape mode	• CDC mode
Tape Status or Clock.	CDC Status or Clock.

Setting the Clock

1.	Turn the ignition key to the ON position.
2.	Press the	PWR	to turn on the unit.
3.	Press the	MENU	, then press the	or	to dis-
	play “CLK SET”.
4.	Press the	PWR	to enter the clock adjustment mode.

5. Use the following buttons and dial to set the clock. (The blink- ing section can be adjusted.)

PWR	: To switch Hour/Minute blink
or	: Adjust the Hour and minute
6. Press the MENU	momentarilfly to complete the Clock set-
ting mode.

Ignition-off Clock Recall

The display will illuminate showing the time and then auto- matically shut off after 5 seconds.

Press the MENU while the ignition switch is in the “OFF ” position.

Switching the Source

You can connect auxiliary equipment (Portable MD player, etc) to this radio via optional AUX-IN cable.(See page 9)

Each time the SRC is pressed, the operation source will

change over as shown below;

Note

If the SRC button is pressed when no Tape has been loaded into the unit, The Tape mode will skip to the AUX or CHANGER mode.

Adjusting the Sound Characteristics

1.	Press the	MENU for more than 2 seconds to enter the			ENGLISH
	the selected item.			or
	audio adjustment mode, then press the
2.	to select the desired adjustment item as table below.
	Press the	or	or rotate the VOL dial to adjust
	Use the following tables as a guide for adjusting the set-
	tings in each item.Adjust within 5 seconds after selecting
	the item. After 5 seconds, the unit returns to previous
	indication.

or

Adjustment Range

EQ OFF (Equalizer will be displayed if set up)

BASS	BAS –5	0	BAS +5
TREBLE	TRE –5	0	TRE +5
LOUDNESS	LOUD OFF		LOUD ON
BALANCE	BAL L9(Full left)	0	BAL R9(Full right)
FADER	FAD R9(Full rear)	0	FAD F9(Full front)
ON VOL	0	50	80
MUTE	0	20	80

•A italicized letter is an initial value.

Tips

• EQ OFF (EQ Display)

Displays the current setting of equalizer curve, if the equal- izer has been set. (See page 5)

• ON VOL (Limit volume)

Adjust the volume at the time of power on. You can adjust with the actual sound.

• MUTE (Mute level)

You can adjust the mute level with the actual sound.

• Settings for BASS, TREBLE, and LOUDNESS can be made to each of the following modes independently:

Each radio band, TAPE, CDC.

E-3