Manuals / Brands / Lawn and Garden / Patio Heater / Blue Rhino / Lawn and Garden / Patio Heater

Blue Rhino 235000 Step 9 – Connect Gas Line to Engine, Step 10 – Attach Top Dome to Emitter, Step 11 – Secure Gas Line

1 42

Download 42 pages, 5.2 Mb

Contact 1-800-762-1142 for assistance.	®
Do not return to place of purchase.

Step 9 – Connect Gas Line to Engine

Attach Gas Line to Control Valve:

Pull collar of Gas Line back.

Insert Gas Line over Control Valve.

Release collar and it should lock in place. (Tip – push Gas Line up from bottom of Post to make a good seating before releasing the collar.)

Gently tug on line to test for proper connection. If Gas Line moves you are not properly connected. Do not proceed until you have a proper connection.

Fully tighten the (4) screws from Step 7.

Step 10 – Attach Top Dome to Emitter

Gently lay Heater on its side using one styrofoam insert to prop up top half.

Align holes in Dome with threaded studs in Emitter brackets.

Secure Dome to Emitter using (3) Cap Nuts. Tighten using 13 mm wrench.

Stand heater upright.

Step 11 – Secure Gas Line

Make sure angled side of Gas Clip pokes up through large hole in Platform.

Tighten screw until Gas Line is held securely in place. Stand Heater upright.

Owner’s manual: model 235000 outdoor patio heater

6/11/04

NOTE:

The white ceramic cone in the top of the engine is an important piece. DO NOT REMOVE.

Section View

Gas Line	Gas Line
Clip	Gas Line
	Bottom View

10

Contents

Page Page Page Before you do anything else read and understand all precautions in Safety First “20 lb.” LP Cylinder Beware of Spiders Need a cylinder or gas Page General Components & Features Additional Requirements Step 1 – Attach Wheel Assembly to Base Step 2 – Attach Legs to Base Step 3 – Attach Platform to Legs Step 4 – Attach Weight Plate to Base Step 5 – Insert Gas Line through Platform/Attach Shroud Cover Step 6 – Attach Small & Medium Dome to Engine Step 7 – Attach Engine to Post Step 8 – Attach Engine/Post to Platform Step 9 – Connect Gas Line to Engine Step 10 – Attach Top Dome to Emitter Step 11 – Secure Gas Line Step 12 – Connect Gas Line to Cylinder Step 13 – Check for Leaks Check Gas Line / Cylinder valve for leaks: Step 14 – Replace Engine Access Panel Step 15 – Install Igniter Battery Before Turning Gas Supply ON Before Lighting Lighting When heater is ON: Re-lighting Shut Down Before Operating After Operation If the problem is: And this condition exists: Then do this Pilot won’t light Pilot won’t stay lit •Do NOT touch or move heater for at least 45 minutes after use •Dome is hot to the touch •Allow dome to cool before touching Between uses: During periods of extended inactivity or when transporting: Page Page Si necesita ayuda llame al No devuelva el artículo al lugar de compra Page Antes de hacer nada más, lea y comprenda todas las instrucciones en ¡La Seguridad, lo Primero Bombona de PL de 9 kg Tenga cuidado con las arañas ¿Necesita una bombona de gas Page Componentes Generales y Características Requisitos adicionales Paso 1 – Asocie la asamblea de la rueda a la base Paso 2 – Acoplar las patas a la base Paso 3 – Acoplar la plataforma a las patas Paso 4 – Acoplar la placa de lastre Paso 5 – Insertar la línea de gas a través de la plataforma Acoplar la tapa de la bombona Paso 6 – Fijar las cúpulas media y pequeña al motor Paso 7 – Acoplar el motor al poste Paso 8 – Acoplar el motor/poste a la plataforma Paso 9 – Conectar la línea de gas al motor Paso 11 – Acoplar la cúpula al emisor Paso 12 – Asegurar la línea de gas Paso 13 – Conectar la línea de gas a la bombona Paso 14 – Comprobar si hay fugas Compruebe si hay fugas en la línea de gas/bombona: Paso 15 – Volver a colocar el panel de acceso al motor Paso 16 – Instalación de la batería de encendido Antes de activar la alimentación de gas (ON) Antes del encendido Encendido Cuando el calentador está encendido (ON) Reencendido Apagado Antes de la puesta en marcha Tras su funcionamiento Si el problema es: La llama piloto no se enciende La llama piloto no sigue encendida El quemador no se enciende La llama del quemador es baja •No toque ni mueva el calentador durante al menos 45 minutos después de su uso •La cúpula está caliente al tacto •Deje que la cúpula se enfríe antes de tocarla Entre uso y uso: Durante períodos largos de inactividad o para su transporte Page Certificaciones: Consumo: Alcance calorífico: Combustible: Tamaño de la bombona: