Manuals / Brands / Lawn and Garden / Patio Heater / Blue Rhino / Lawn and Garden / Patio Heater

Blue Rhino 235000 Then do this, Carbon build-up, Pilot won’t light, Thick black smoke, If the problem is:, Burner won’t light, Burner flame is low, Pilot won’t stay lit

1 42

Download 42 pages, 5.2 Mb

	Contact 1-800-762-1142 for assistance.			®
	Do not return to place of purchase.


	Troubleshooting

	If the problem is:	And this condition exists:		Then do this
	Pilot won’t light	Tank valve is closed		Open valve
		Blockage in orifice or pilot tube		Clean or replace orifice or pilot tube
		Air in gas line		Open gas line and bleed it (pressing
	Note: Heater operates at reduced efficiency			control knob in) for not more than 1
	below 40ºF (5ºC).			- 2 minutes or until you smell gas
		Low gas pressure with tank valve fully		Turn tank valve OFF and replace tank
		open
		Igniter fails		Use match to light pilot; obtain new
				igniter and replace

	Pilot won’t stay lit	Dirt built up around pilot		Clean dirt from around pilot
		Connection between gas valve and		Tighten connection and perform leak
		pilot assembly is loose		check

		Thermocouple is not operating		Replace thermocouple
		correctly

	Burner won’t light	Gas pressure is low		Turn tank valve OFF and replace tank

		Blockage in orifice		Clear blockage

		Control knob is not in ON position		Turn control knob to ON

	Burner flame is low	Gas pressure is low		Turn tank valve OFF and replace tan
		Outdoor temperature is less than 40ºF		Use a full tank
		and tank is less than 1/4 full

		Supply hose is bent or kinked		Straighten hose

		Control knob fully ON		Check burner and orifices for
				blockage

	Emitter glows uneven	Gas pressure is low		Turn tank valvue OFF and replace tank

	Note: Bottom 1” of emitter normally does	Base is not on a level surface		Place heater on a level surface
	NOT glow.
	NOT glow.	Heater is level		Clean burner
		Heater is level		Clean burner

	Carbon build-up	Dirt or film on reflector and emitter		Clean reflector and emitter

	Thick black smoke	Blockage in burner		Remove blockage and clean burner
				inside and outside

Owner’s manual: model 235000 outdoor patio heater

6/11/04

16

Contents

Page Page Page Before you do anything else read and understand all precautions in Safety First “20 lb.” LP Cylinder Beware of Spiders Need a cylinder or gas Page General Components & Features Additional Requirements Step 1 – Attach Wheel Assembly to Base Step 2 – Attach Legs to Base Step 3 – Attach Platform to Legs Step 4 – Attach Weight Plate to Base Step 5 – Insert Gas Line through Platform/Attach Shroud Cover Step 6 – Attach Small & Medium Dome to Engine Step 7 – Attach Engine to Post Step 8 – Attach Engine/Post to Platform Step 9 – Connect Gas Line to Engine Step 10 – Attach Top Dome to Emitter Step 11 – Secure Gas Line Step 12 – Connect Gas Line to Cylinder Step 13 – Check for Leaks Check Gas Line / Cylinder valve for leaks: Step 14 – Replace Engine Access Panel Step 15 – Install Igniter Battery Before Turning Gas Supply ON Before Lighting Lighting When heater is ON: Re-lighting Shut Down Before Operating After Operation If the problem is: And this condition exists: Then do this Pilot won’t light Pilot won’t stay lit •Do NOT touch or move heater for at least 45 minutes after use •Dome is hot to the touch •Allow dome to cool before touching Between uses: During periods of extended inactivity or when transporting: Page Page Si necesita ayuda llame al No devuelva el artículo al lugar de compra Page Antes de hacer nada más, lea y comprenda todas las instrucciones en ¡La Seguridad, lo Primero Bombona de PL de 9 kg Tenga cuidado con las arañas ¿Necesita una bombona de gas Page Componentes Generales y Características Requisitos adicionales Paso 1 – Asocie la asamblea de la rueda a la base Paso 2 – Acoplar las patas a la base Paso 3 – Acoplar la plataforma a las patas Paso 4 – Acoplar la placa de lastre Paso 5 – Insertar la línea de gas a través de la plataforma Acoplar la tapa de la bombona Paso 6 – Fijar las cúpulas media y pequeña al motor Paso 7 – Acoplar el motor al poste Paso 8 – Acoplar el motor/poste a la plataforma Paso 9 – Conectar la línea de gas al motor Paso 11 – Acoplar la cúpula al emisor Paso 12 – Asegurar la línea de gas Paso 13 – Conectar la línea de gas a la bombona Paso 14 – Comprobar si hay fugas Compruebe si hay fugas en la línea de gas/bombona: Paso 15 – Volver a colocar el panel de acceso al motor Paso 16 – Instalación de la batería de encendido Antes de activar la alimentación de gas (ON) Antes del encendido Encendido Cuando el calentador está encendido (ON) Reencendido Apagado Antes de la puesta en marcha Tras su funcionamiento Si el problema es: La llama piloto no se enciende La llama piloto no sigue encendida El quemador no se enciende La llama del quemador es baja •No toque ni mueva el calentador durante al menos 45 minutos después de su uso •La cúpula está caliente al tacto •Deje que la cúpula se enfríe antes de tocarla Entre uso y uso: Durante períodos largos de inactividad o para su transporte Page Certificaciones: Consumo: Alcance calorífico: Combustible: Tamaño de la bombona: