BOB MA0201 operating instructions Seat Safety, Shock Absorbers

Fig. 22

Stroller with handle folded

Brake pads shown aligned to rim

3/16” clearance between brake pad & rim

Tire

Rim

Fig.16

10mm Nut

Brake Pad Nut

Brake

Pad 3/16”

Fig. 15

Brake

Body

Sport Utility Stroller OWNER’S MANU

clockwise direction. To set the parking brake, squeeze the

brake lever and press and hold the

button down, then

release lever (Fig.

13 &14). When the brake is properly set, the button will

remain depressed and the lever will

appear as shown in Fig. 14. To release the parking brake,

simply squeeze the brake lever and the button will “pop” up. For the parking brake to work correctly, it is critical that the brake be adjusted properly. Squeeze the brake lever and verify that

the brake pads contact the rim as shown in Fig. 16. If they are misaligned, use a 10mm wrench to loosen brake pad nuts, slide pads into correct position and tighten securely. The cable tension is pre- adjusted at the factory yet the brake cable will need periodic adjustment (as the cable stretches slightly and the black cable housing compresses over time). To adjust cable tension, there are two barrel adjusters in the brake assembly (Fig. 10 &13). To tighten the cable, loosen the lock ring and turn the barrel adjuster in the counter clockwise direction. Secure the barrel adjuster in the new position by tightening the lock ring against the caliper or brake lever body. There should be a 3/16” clearance between the rim and brake pads as shown in Fig. 15. If gap is not equal on each brake pad, you can reposition the brake on the frame by loosening the 10 mm nut (Fig. 16) with a 10mm wrench, adjust to the gap shown in Fig. 15 and re-tighten the same nut. If you do not understand these instructions, or feel the brake is adjusted incorrectly, take the stroller to your dealer for proper adjustment. If your brake pads (Fig. 10) are worn, see your dealer for replacements.

8SUN CANOPY: The stroller features a two position canopy. To fully open the canopy, rotate the assembly forward until the fabric is taut. The rear safari flap should be freed from the Velcro to give additional sun protection. To reduce the size of the sun canopy, pull the canopy toward the handlebar. The additional fabric can be gathered by pulling the canopy (Fig. 1) drawstring and securing the cord lock.

9 SEAT SAFETY
HARNESS: To secure your	Shoulder
child in the seat, put one	Strap
strap (grey) over each
shoulder and snap the male
buckle into the female
receiver on the crotch strap	Fastener
(Fig. 17). Adjust shoulder
straps to be snug and
secure (Fig. 18). Connect
and adjust the sternum strap
(red), see Fig. 19.
WARNING: Never place
passengers in the stroller
without securing them in the
harness. Unrestrained	Fig. 17 Place straps over shoulders
passengers can affect the
	and secure to buckle.
control of the stroller.
Passenger Weight Limit -	70 Pounds (32 Kilograms)

10RECLINING SEAT: Set parking brake before making any seat adjustments. To recline the seat, rotate the ladder locks (Fig. 20) forward thus releasing the reclining straps. To raise the seat, pull the

reclining straps until you obtain	Shoulder
the desired position. The seat
	Strap
back can be adjusted to recline
anywhere between the fully
upright position and the fully
reclined position (Fig. 20 & 21).
11 SHOCK ABSORBERS: The
suspension system features two
shock positions to provide a
comfortable ride for kids of
different weights. The two	Fig. 18 Securely adjust shoulder straps
positions are shown in Fig. 2.
Position 1 is intended for
occupants up to 40 lbs. ( 18 kg),	Sternum
while position 2 is intended for	Strap
occupants from 40 to 70 lbs. (18
to 32 kg) total. The stroller
features a sliding track and spring
loaded shock axle that
automatically locks in place when
it aligns with either of the two
shock settings. Shock position
adjustments should be made with
the stroller unloaded. The shocks	Fig. 19 Connect Sternum Strap
will lock into position 1 when
unfolding the stroller. To use the	Seat Reclining
stiffer shock position, move the
	Ladder Locks
shock from position 1 to position
2 by depressing the shock release
button (Fig. 2) with one hand, and
with the other hand, lift slightly
and pull the shock backward.
When the shock axle is properly
aligned in position 2, the axle will
“snap” into place. Repeat this	Fig. 20
process for the second shock. To
move the shock from position 2
to position 1, reverse the above	Reclining
process for both shocks.
	Strap Loops
12 FOLDING: Remove children
from stroller. Remove the contents
of the Low Boy cargo pouch. The
shock absorbers must be in
position 1 (Fig. 2) before folding.
Press both the right and left
handlebar release levers (Fig. 3),	Fig.21 Seat in fully reclined position.
and fold the handlebar forward
as shown in Fig. 22. Locate the

frame release handle underneath the seat (Fig. 23) and pull upwards sharply. This will allow the lower frame to fold together, as shown in Fig. 24. The folded stroller can be made even more compact by removing the front and rear

wheels. The front wheel is

removed by opening the brake quick release (Fig. 10), opening the wheel quick release and

removing the wheel (see section 6). Note that it is

often easier to open the

brake quick release before you fold the handlebar. The rear

wheels are removed by opening the rear wheel quick release (Fig. 4), and removing the wheels.

The Wrist Strap can be used to keep the stroller in the folded

position for transport and storage. With the stroller folded, loop the end of the wrist strap around the handlebar and back to the rear axle and fix the Velcro surfaces together (Fig. 25).