D6600 Card Installation Guide 1.0 Introduction
1.0Introduction
These instructions describe how to install replacement or upgrade cards in the Conettix D6600 Communication Receiver/Gateway (D6600).
The D6600 provides eight line card slots and one CPU card slot. Be sure to install the cards in the correct slots. Refer to Figure 2.
2.0Installation Considerations
•The D6600 provides eight line card slots, one Conettix D6641 Telephone Line Card (D6641) and one Conettix D6645 Telephone Line Terminator Card (D6645)
•You must install a D6640 Telephone Line Card (D6640) or a D6641 and a D6645 together.
For SafeCom applications:
•You must install a Conettix D6690 SAFECOM Line Card (D6690) and a Conettix D6695 SAFECOM Line Terminator Card (D6695) together.
•A Conettix D6691 SAFECOM Expansion Card (D6691) provides an additional four channels for locations that require more than four channels.
•A D6690 with a D6691 requires two adjacent slots and two D6695s.
3.0Installation Instructions
Figure 2: D6600 Rear Panel
| 2 | 4 |
|
| 3 |
Bosch Security Systems |
| |
Fairport, NY | USA |
|
|
| 1 |
|
| 2 |
| 1 | 3 |
|
| |
|
| 4 |
| B |
|
| A |
|
| T |
|
| T |
|
| E |
|
| R | 5 |
| Y |
|
| Input: |
|
| 100 - 120/ |
|
| 220 - 240V~ |
|
| 50 - 60 Hz |
|
| 2.5 Amps |
|
4
1 - Conettix D6672 Com 1 Expansion Kit slot (opt) 2 - Conettix D6615 CPU Terminator Card slot
3 - Line termination slot covers
4 - Card slot screw (two per plate)
5 - D6645 (factory installed)
Figure 3: D6600 Internal Front View
5 2
3
6
8 |
1 |
1 | 5 |
2 | 4 |
|
3
2
4 | 7 |
If the door does not shut properly on any card installation, check that the card is fully seated.
Figure 1: D6600 Front Panel
1 - D6641 (factory installed)
2 - Plastic card guides
3 - Plastic tab for installing or removing CPU card
4 - Conettix D6610 CPU Line Card (D6610)
5 - Ribbon cable tabs
6 - Ribbon cable
7 - LED enable cable
8 - D6600 backplane
1 | 2 | 3 | A | B |
00/00 00:42 | 5 | 6 | C | D |
4 | ||||
7 | 8 | 9 | E | F |
M/E | CAN |
COMMUNICATIONS RECEIVER/GATEWAY |
| POWER |
| SYSTEM TROUBLE |
| 2 |
3 | ACKNOWLEDGE |
OL/LF |
1
1 - Removable line card slot covers
2 - D6641 (factory installed)
3 - Door handle, secures with magnets
Refer to Figure 1, Figure 2, and Figure 3 in Sections 3.1, 3.2, and 3.3 on pages 2 and 3 for instructions.
3.1Termination Card Installation
To install the D6645 or D6695 Termination Card:
1.If you are installing a replacement termination card, remove the old card:
a.Open the D6600 front door and pull the corresponding line card until it disconnects from the termination card and the D6600 backplane.
b.Remove the two screws securing the old termination card to the rear panel.
c.Remove the old termination card.
2.If you are installing a new termination card, locate the correct slot and remove the two screws securing the blank plate to the rear panel.
2 | Bosch Security Systems, Inc. 2/07 |
