D6600 Card Installation Guide 3.0 Installation Instructions
3.Position the new termination card so the
4.Install the new line card (refer to Section 3.2 Line Card Installation) or push the existing line card back into the D6600 until it connects to the termination card and the backplane.
5.Close the D6600 door.
3.2Line Card Installation
To install the D6640, D6641, or D6690:
1.Open the D6600 front door.
2.If you are installing a replacement line card, remove the existing card:
a.Pull the line card until it disconnects from the termination card and the D6600 backplane.
b.Remove the line card from the D6600.
3.Ensure the new termination card is installed in the correct slot (refer to Section 3.1 Termination Card Installation).
Two termination cards are required if using the D6691.
4.If necessary, attach the D6691 to the line card. Refer to Section 3.4 Expansion Card Installation.
5.Align the line card in the top and bottom guides and push until it connects with the termination card and the D6600 backplane.
6.Close the D6600 door.
7.Program the line card. Refer to the Conettix D6600/D6100 Program Entry Guide
(P/N: 4998122702).
3.3CPU Card Replacement
To replace the D6610 and D6615 CPU:
1.Remove power from the D6600 and open the door.
2.Pull the D6610 by the white plastic tab until it disconnects from the D6615 and the D6600 backplane.
3.Remove the screws securing the D6615 to the D6600 rear panel and remove the card.
6.Install the new D6610:
a.Orient the card so that the ribbon cable connector faces to the right and align the card in the top and bottom guides.
b.Slide the card partially into the D6600.
c.Connect the ribbon cable to the D6610.
d.Push the card into the D6600 until it connects with the D6615 and the D6600 backplane.
7.Close the D6600 door and apply power.
8.Load the backup CPU parameters into the new D6610 using the D6200 Software. Refer to the
D6200 Operation and Installation Guide (P/N:
4998154991).
3.4Expansion Card Installation
To install the D6691 on the D6690 (refer to Figure 4):
1.Verify the compact flash card and the SIMM are installed on the D6690.
2.Attach the four hexagonal
3.Align the D6691 mounting holes to the four standoffs so the long pins on the D6691 align with the
4.Push firmly until the pins connect with the socket and the D6691 rests squarely on the four standoffs. You might have to rock the D6691 gently until the pins connect completely.
5.Secure the D6691 to the four standoffs with screws and washers.
6.Install the expanded D6690 (refer to Section 3.2 Line Card Installation).
For specifications on individual modules, refer to the corresponding installation manual:
• Conettix D6600/D6100 Operation and Installation Guide (P/N: 4998122704)
•D6690 SafeCom System Guide (P/N: 48536)
On the rear panel, the CPU slot is the first slot to the right of the larger slot designated
Figure 4: Expansion Card Installation
for the D6672.
2 1
1
4.Remove the existing D6610:
a.Disconnect the
b.Slide the card out until you can easily reach the ribbon cable connector.
c.Disconnect the ribbon cable and remove the card.
5.Install the new D6615:
a.Orient the card so that the
b.Secure the card to the rear panel with two screws.
1 | 1 |
4 |
6 | 3 |
5 |
|
| 1 |
| 1 |
1 - | 4 - | D6690 | |
2 - | D6691 | 5 - | SIMM |
3 - | 6 - | Compact flash card |
Bosch Security Systems, Inc. 2/07 | 3 |