Installation
6. Connect Wiring
WARNING:
Use only spring type wire nuts (included) to make electrical connections. Replacement wire nuts must be rated for a minimum of (2) #18ga wires and a maximum of 4 #14ga wires, UL & CSA rated to 600V and 302º F/ 150º C. Request #189692 when ordering from
BSH.
For Internal Blower Use:
See Figure 1 or 2, page 3.
1.Remove electrical knockout behind J box and install 1/2” conduit connectors.
2.Run 120V AC 60Hz, 15A supply wires through 1/2” conduit to hood electrical knockout behind J box cover.
3.Connect blower cord wires to house wiring through electrical knockouts. Use wire nuts supplied (white to white, black to black, green to green).
4.Connect blower cord at white connector behind connector access panel (if not already connected). Verify that connectors are tightly connected.
For Remote Blower Use:
See Figure 3, page 3.
1. | Remove 2 hood electrical knockouts and install |
| 1/2” conduit connectors. |
2. | Run black, white and green supply wires through |
| 1/2” conduit to hood electrical knockout behind |
| J box. |
3. | Connect power supply wires to hood wires behind |
| J box (white to white, black to black, green to |
Accessories
The following accessories are available from your Bosch dealer or through Bosch Service:
Accessory | Model # | |
6” Duct Covers | 30” | 36” |
Biscuit | DCZ7607UC | N/A |
Black | DCZ7606UC | DCZ9666UC |
Stainless Steel | DCZ7605UC | DCZ9665UC |
White | DCZ7602UC | DCZ9662UC |
12” Duct Covers | 30” | 36” |
Biscuit | DCZ7207UC | N/A |
Black | DCZ7206UC | DCZ9266UC |
Stainless Steel | DCZ7205UC | DCZ9265UC |
White | DCZ7202UC | DCZ9262UC |
Recirculation Kit | 30” | 36” |
Biscuit | DRZ7007UC | N/A |
Black | DRZ7006UC | DRZ9066UC |
Stainless Steel | DRZ7005UC | DRZ9065UC |
White | DRZ7002UC | DRZ9062UC |
Charcoal Filter | DHZ7960UC | |
3 1/4 x 10Transition | DHZ3410UC | |
Blowers* |
|
|
Integral Blower, 400 CFM | DHG4001UC | |
Integral Blower, 600 CFM | DHG6001UC | |
Remote Blower, 600 CFM | DHG6003UC | |
Remote Blower, 1000 CFM | DHG1003UC | |
*for use with DAH95 models only |
|
|
Figure 6 - Remote Blower Pigtail Assembly
green). Use wire nuts supplied. |
4. Run 5 wires (#14 AWG) in 1/2” conduit from the |
remote blower to the electrical knockout behind |
the remote wire cover. |
N GND L1
( PROVIDED W/HOOD )
5. | Connect remote blower wiring to “pigtail” wires |
| behind remote wire cover with wire nuts supplied |
| (white to white, black to black, green to green and |
| black to brown, white to white, red to red and |
| blue to blue) See Figure 6. |
6. | Connect other end of “pigtail” at white connector. |
| Verify that connectors are tightly connected. |
7. Reassemble Hood |
Reattach the following:
1.Connector access panel (internal blower only)
2.J box
3.Remote wire cover (remote blower use only)
4.Back filter rail
5.Filters
| BLACK |
|
|
| WHITE | BROWN | BLUE |
|
| ||
| BROWN |
| RED |
|
|
| |
M | WHITE |
|
|
RED |
|
| |
|
|
| |
| BLUE |
|
|
GND |
|
|
|
5