OPERATING THE: SHE4AM0
•You are now ready to start a new cycle
Note: You cannot cancel a cycle with the Child Lock feature activated.
Setting Options (Rinse Agent Amount / Extra Dry Heat Activa- tion)
|
|
| • Door must be closed. Press the “ON/ | |
SHE4AM1 |
| OFF” button to turn the unit on. | ||
| • One of the Wash Cycle Indicator Lights | |||
|
|
| will be flashing to show you are in the | |
|
|
| Wash Cycle selection mode. | |
|
|
| • To enter the Options Setup Mode, | |
|
|
| press and hold down the “>” button, | |
|
|
| then press and release the “START RE- | |
| WARNING | SET” button, then release the “>” button. | ||
| • The “Clean” Indicator Light and at least one addition Indicator Light | |||
You could be seriously scalded if you allow hot water to splash | ||||
will be flashing to show you are in the Options Setup Mode. | ||||
out of the dishwasher. OPEN THE DOOR CAREFULLY during any | ||||
• Press the “>” button to select the option you would like to adjust | ||||
wash or rinse cycle. Do not fully open the door until water noises | ||||
o | If the “CLEAN” and “RINSE AGENT” Indicator Lights are flashing | |||
have stopped. | ||||
To Start Unit: |
| you are ready to set the amount of Rinse Agent the unit will | ||
| dispense. | |||
|
|
| ||
• Door must be closed. Press the “ON/OFF” button to turn the unit | o If the “CLEAN” and “SANITIZED” Indicator Lights are flashing you | |||
| on. | |||
|
| are ready to turn your Extra Dry Heat option on/off. | ||
|
|
| ||
• | One of the Wash Cycle Indicator Lights will be flashing to show | To Set the Amount of Rinse Agent Dispensed | ||
| you are in the Wash Cycle selection mode. | |||
| NOTE: If your glasses have spots you need more Rinse Agent. If your | |||
• Press the “<” or “>” button to select the desired wash cycle. | ||||
glasses have streaks you need less Rinse Agent. | ||||
|
| |||
• | If desired select the “HALF LOAD” or DELAY START” features at | • With the “CLEAN” and “RINSE AGENT” Indicator Lights flashing. | ||
| this point. | |||
| • | Press the “<” button to change the amount of Rinse Agent Dis- | ||
| o If you would like to delay the start time of the dishwasher press | |||
| pensed. | |||
| the “DELAY” button until the desired delay time (3/6/9 hrs.) | |||
| • As you press the “<” button you will notice the Wash Cycle Indica- | |||
| shows on the Indicator Lights. | |||
| o In addition to your Wash Cycle selection, for small loads of | tor Lights illuminating | ||
| o | If none of the Wash Cycle Indicator Lights are illuminated, the | ||
| lightly soiled dishes press the “HALF LOAD” button. This will | |||
| save energy and water (SHE4AM1# only). |
| Rinse Agent Dispenser is turned off. | |
• | Press the “START” button to begin the cycle (Wash Cycle Indica- | o | If one of the Wash Cycle Indicator Lights are illuminated, the | |
| tor Light will stop flashing and the “Active” Indicator Light will |
| Rinse Agent Dispenser is set to deliver the lowest charge of | |
| illuminate) |
| Rinse Agent. | |
Note: Rinse Agent Indicator Light will be illuminated if the unit needs | o | If two of the Wash Cycle Indicator Lights are illuminated, the | ||
Rinse Agent. |
| Rinse Agent Dispenser is set to deliver a medium charge of | ||
Child Lock |
| Rinse Agent. | ||
o | If three of the Wash Cycle Indicator Lights are illuminated, the | |||
• After pressing the “START” button you can activate the Child Lock | ||||
| Rinse Agent Dispenser is set to deliver the largest charge of | |||
| feature. |
| ||
|
| Rinse Agent. | ||
|
|
| ||
• Press and hold down the “<” button until Child Lock Indicator Light | • Press “START” to save your settings. | |||
| illuminates (Light goes out when button is released). | |||
| To Turn the Extra Dry Heat On or Off | |||
• Now any button you press (except ON/OFF) will not function and | ||||
• With the “CLEAN” and “SANTITIZED” Indicator Lights flashing. | ||||
| the Child Lock Indicator Light illuminates when pressing. | |||
• | To deactivate, press and hold the “<” button until the Child Lock | • Press the “<” button to change the Extra Dry Heat setting. | ||
| Indicator Light goes out. | • As you press the “<” button you will notice the Wash Cycle Indica- | ||
To Cancel the Cycle: | tor Lights illuminating | |||
• Press and hold the “START/RESET” button until the “Active” Indica- | o | If none of the Wash Cycle Indicator Lights are illuminated, the | ||
| tor Light goes out. |
| Extra Dry Heat option is turned off. | |
• Wait for about 1 minute for the dishwasher to drain. | o | If one of the Wash Cycle Indicator Lights are illuminated, the | ||
• Press the “ON/OFF” button. |
| Extra Dry Heat is turned on. | ||
|
|
• Press “START” to save your settings.
13