Boss Audio Systems ME-20 Rear Panel

10

Names of Things and What They Do

Rear Panel

ME-20-rear-panel.eps_70

1. SECURITY LOCK ( )

http://www.kensington.com/

2. INPUT Jack

Connect your guitar here.

* The INPUT jack doubles as a power switch. Inserting a plug into the INPUT jack turns on

the power; the power is switched off when the plug is disconnected. Be sure to unplug the

cable from this jack when the ME-20 is not in use.

3. AUX IN Jack

Connect a CD or MP3 player here to practice with sounds from these devices.

* You cannot adjust the volume of the AUX input. Adjust the volume on the connected device.

* Do not use a cable that contains a resistor to connect external devices to the AUX IN jack.

Use of such cables may make sounds from connected devices inaudible.

* No effects are applied to the AUX input signal.

4. OUTPUT L/MONO, R Jacks

Connect an amp or mixer here.

5. PHONES (Headphones) Jack

Connect stereo headphones here.

When headphones are connected to the PHONES jack, tonal adjustments are

applied so the sound is close to that produced by the guitar amp.

6. FOOT SW (Footswitch) Jack

Connect an optional footswitch (such as the FS-6) here.

The footswitch functions differently in Manual mode and Memory mode.

When in Manual mode:

Switches the OD/DS Solo on/off.

Switches the Bypass/Tuner on/off.

When in Memory mode:

Bank up, Bank down

7. DC IN (AC Adaptor) Jack

Connect the optional AC adaptor (PSA series) here.

* Use only the specified AC adaptor (PSA series).

3 4 71 2 5 6

ME-20_e.book 10ページ２００７年９月１０日　月曜日　午後６時２２分

Contents

Main Main Features ME-20_e.book 2 Before using this unit, make sure to read the instructions below, and the Owners Manual. Do not open (or modify in any way) the unit or its AC adaptor. Page IMPORTANT NOTES Additional Precautions Repairs and Data Maintenance Printing Conventions and icons in This Manual (p.**) Contents Names of Things and What They Do Front Panel 1. Parameter Knobs Page Page Rear Panel Installing Batteries Connections Turning On the Power Turning Off the Power Recommended Settings Tuning the Guitar (Bypass/Tuner) 4. First do a rough tuning so that the name of the note for the string appears in the display. (C) (C ) (D) (D ) (E) (F) (F ) (G) (G ) (A) (A ) (B) Too high Tuned Too low Introduction to Effects and Parameters About the Effect Connection Sequence OD/DS SOLO OD/DS (Overdrive/Distortion) OD/DS Type List Introduction to Effects and Parameters MOD (Modulation) MOD Type List DELAY DELAY Type List EQ (Equalizer) WAH MASTER LEVEL THRESHOLD NS (Noise Suppressor) Creating Sounds Easily (EZ EDIT) EZ EDIT Setting List Saving and Calling Up Tones (Memory Mode) Manual Mode and Memory Mode Patches and Banks The MEMORY indicator disappears. Switching Between Manual and Memory Mode Saving Tones (Write) 2 1,3 2 Calling Up and Using Saved Sounds (Patch Change) (1) (2) (3) (1) Switching Banks Changing Patch Settings (Patch Edit Mode) 5 2,4 1 Other Functions Using Footswitch Pedals When Connecting an FS-5U Connecting a Footswitch Pedal When Connecting Two FS-5Us or an FS-6 BA If using an FS-6 switch, set the MODE and POLARITY switches as shown below. Returning the ME-20 to Its Factory Settings (Factory Reset) 2 3,4 Adjusting the Expression Pedal Depress the toe of the expression pedal until its all the way down, and press [WRITE]. 4. Patch List Factory Settings DEPTH LEVEL BANK * The OD/DS Solo level is set to 25. Factory Settings Type List THRESH- OLD Blank Chart BANK DEPTH LEVEL Blank Chart Type List THRESH- OLD Troubleshooting bt Appears in the Display Patches Cannot Be Switched No Sound/Volume is Low Power does not turn on Specifications Index Page NOTICE AVIS FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT *G6027123-03* G6027123R1 3RTC