Bostitch SW9040 5/8 SW9040 3/4 SW9040 7/8 manual D14135 Clinchers, D16124 Deep Clinchers

ITEM	PART NO.	DESCRIPTION	ITEM	PART NO.	DESCRIPTION
NO.			NO.
47.	LW10	#10 Lock Washer	52.	D60009	Valve Stem
48.	UP2912.3	3/32 x 3/4” Cotter Pin	53.	851201	O-Ring .301 x .070
49.	D14164	Pusher Spring	54.	D60008	Valve Body
50.	UB2814.2	Pin, Spring .094 x .88	55.	86458	O-Ring 1/16”x 1/2” ID
51.	D60054	Spring, Valve	56.	86998	O-Ring 1/16”x 9/16” ID
			57.	86459	O-Ring 1/16”x 5/8” ID

VARIABLE PARTS

ITEM NO.	DESCRIPTION	STANDARD PARTS	OPTIONAL PARTS
11.	Driver	D16170 (long)	D16178 (short)
30.	Clincher	D16124 (deep)	D16124B (deep pointed)
			D14135 (shallow)
33.	C’ Balance Hanger		D16106A
29.	Magazine Assembly	D16169A	D16164A
		[5/8” (15.9mm)	[7/16” (11.1mm)
		3/4” (19.1mm)	5/8” (15.9mm)
		and 7/8” (22.2mm)	and 3/4” (19.1mm)
		staples]	staples]

D14135 CLINCHERS

Approx. Clincher Adjusting
Clamp Setting	6	5	4	3	2	1
				5/8”
(2) A Board-Blind				(15.9mm)
				Leg
					3/4”
(2) A Board-Through					(19.1mm)
					Leg
		7/16”
(2) B Board-Blind		(11.1mm)
		Leg
			5/8”
(2) B Board-Through			(15.9mm)
			Leg
			7/16”
(2) C Board-Blind			(11.1mm)
			Leg
			5/8”
(2) C Board-Through			(15.9mm)
			Leg

To obtain maximum efficiency from the staple closure, it is important that the staple be clinched properly. Proper clinching for any thickness board may be obtained by adjusting the clincher setting with staples of proper leg length.

Use the proper length staples for the thickness of work to be stapled, otherwise unnecessary pressure is exerted and staple crowns and legs will be distorted, or the clinch will be too loose.

Staple driven completely through two thicknesses of corrugated board and clinched on underside.

Staple clinched “blind” when desired, in two thicknesses of corrugated board.

D16124 DEEP CLINCHERS

Approx. Clincher Adjusting
Clamp Setting	6	5	4	3	2		1
						3/4”
(2) A Board-Through						(19.1mm)
						Leg
						3/4”
(2) AB Board-Blind						(19.1mm)
						Leg
							7/8”
(2) AB Board-Through							(22.2mm)
							Leg

D14135 clinchers are for shallow penetration as in single wall board and will clinch inside board without damage to contents. D16124 clinchers are for deep penetration as in double wall board.

CAUTION: WHEN USING DEEP PENETRATION CLINCHERS, IT MAY BE NECESSARY TO USE A FILLER TO PREVENT DAMAGE TO MERCHANDISE. D16124 CLINCHERS MAY ALSO BE USED FOR STAPLING THROUGH SINGLE WALL BOARD PROVIDED A FILLER IS USED TO PREVENT DAMAGE TO CONTENTS OR CLINCHERS.

CLINCHER ADJUSTMENT:

Always disconnect air supply: 1.) Before making adjustments; 2.) When servicing the tool; 3.) When clearing a jam; 4.) When tool is not in use; 5.) When moving to a different work area, as accidental actuation may occur, possibly causing injury.

When working on air tools note the warnings in this manual and use

extra care when evaluating problem tools.

Clincher adjustment for depth of penetration is obtained by loosening the clincher adjusting clamp screw on front of machine and moving it up or down. When in its highest position, the clinchers are set for the shallowest staple penetration. Lowering the clinchers increases the penetration. After establishing the setting, tighten adjustment screw.

NOTE: The D16-2AD is equipped with a driver to countersink the crown of the staple below the surface of the box. The shorter driver, available on order, will allow the crown of the staple to rest on the top of the box.