Terreon® Multi-Fount Washfountains

Parts and Service Guide

 

 

 

Troubleshooting BIR3 Components

CAUTION: Turn off water supplies to unit before troubleshooting.

Problem:

An individual operating station drips and fails to shut off.

Cause:

There is debris trapped between the diaphragm and the valve seat.

Solution:

Remove debris between diaphragm and the valve seat.

Disconnect the plug from the battery to the circuit board of the problem valve. Remove the three #8 Phillips-head screws that hold the solenoid valve assembly together. Be careful not to lose the armature or spring (see previous page). Remove the diaphragm. Remove any particles that are trapped between the diaphragm and the valve seat.

Rinse off the diaphragm and inspect for damage. Make sure the center orifice and both small side orifices are open. Reassemble in reverse order, being careful not to overtighten the Phillips-head screws or you may crack the plastic valve body. Tighten until the armature plate makes contact with the plastic body. Reconnect the battery plug per dia- gram. Turn on water supplies to the unit.

Problem:

An individual operating station fails to turn on or off.

Cause:

Excessive line pressure.

Solution:

Install Pressure Reducing Valve.

Check the static line pressure. If the pressure exceeds 80 psi, install a pressure reducer valve at the street main. Excessive line pressure (over 60 psi) will shorten the life of any valve.

Problem:

An individual operating station fails to turn on or off.

Cause:

A dead or faulty battery.

Solution:

Test the station to determine cause and replace battery if

required.

 

Disconnect the plug from the battery to the circuit board of the problem valve. Disconnect the plug from the battery to the circuit board of an adjacent valve. Connect the battery plug from the adjacent working valve to the problem valve. Wait for ten seconds. Activate the problem station’s sensor ten times. The station should turn on. If the station turns on, and cycles normally, replace the battery.

Cause:

Faulty sensor eyes.

Solution:

Test station to determine cause; replace sensor eyes if required.

Disconnect the sensor cable from the circuit board of the problem valve. Disconnect the sensor cable from the circuit board of an adjacent working valve. Connect the sensor cable from the adjacent working valve to the problem valve. Activate the problem station’s sensor. The station should turn on. If the station turns on and cycles normally, replace the sensor eyes.

Cause:

Faulty solenoid valve.

Solution:

Test station to determine cause; replace solenoid valve if required.

Remove the screw, circuit board and standoff from the problem valve. Remove the battery holder. With a good working battery, briefly contact the solenoid valve directly with the battery as shown in the Open Valve figure. The contact should cause the valve to open. With the battery holder removed, briefly contact the sole- noid valve with the battery in the position shown in the Closed Valve Figure. This should cause the valve to close. If the valve does not operate when directly contact- ed with a good battery, and the solenoid valve has already been cleaned as outlined at the beginning of this troubleshooting section, replace the solenoid valve.

If problems persist:

OPEN VALVE

CLOSED VALVE

Pass your hand in front of the problem station, while at the same time looking to see if the indicator light on the cir- cuit board flashes (the indicator light is located near the hole in the circuit board where the standoff is mounted). If it does not flash, and the battery and sensor eyes have already been tested as outlined above, the problem may be with the circuit board. Make a note of the numbers printed on the circuit board, then contact your Bradley represen- tative for assistance.

18

1/30/2008

Bradley Corporation • 215-1447 Rev. F; EN 07-005A

Page 17 Page 19
Page 18
Image 18
Bradley Smoker Indoor Furnishings manual Troubleshooting BIR3 Components
Page 17 Page 19

Indoor Furnishings specifications

Bradley Smoker Indoor Furnishings represent a refined choice for those who desire quality, functionality, and aesthetic appeal in their smoking experience. Renowned for their innovative designs and advanced technologies, Bradley Smokers have carved a niche in the realm of indoor cooking, specifically for smoking meats, fish, and even vegetables.

One of the standout features of Bradley Smokers is their unique bisquette smoking system. This technology utilizes compressed wood bisquettes that are designed to provide consistent smoke for a prolonged period. Each bisquette burns for about 20 minutes before being automatically pushed off the burner, ensuring that users receive a continuous flow of smoke without the risk of creosote buildup, often associated with traditional wood smoking methods. This patented system not only simplifies the smoking process but also enhances the flavor of the food, producing a clean and rich taste that is highly revered by culinary enthusiasts.

The building materials utilized in Bradley Smoker Indoor Furnishings are of high caliber, often featuring stainless steel construction that offers durability and resilience against the elements, whether for indoor or outdoor use. This material also makes cleaning easier, which is an important consideration for any cooking appliance. The insulated design aids in maintaining temperature consistency, allowing for more precise control over the cooking environment.

User-friendliness is another critical characteristic of Bradley Smokers. Many models come equipped with digital controls, which allow users to easily set and monitor temperatures and smoking times. This technology is complemented by the inclusion of temperature gauges that provide real-time feedback, making it accessible even for beginners.

Versatility is a hallmark of Bradley Smokers, with various models allowing for cold smoking and hot smoking capabilities. This adaptability means that users can experiment with a wide range of foods, from traditional smoked meats to artisanal cheese, creating opportunities for culinary creativity.

In summary, Bradley Smoker Indoor Furnishings stand out for their innovative bisquette smoking system, durable construction, user-friendly digital controls, and versatile smoking capabilities. These features combine to create an enjoyable and straightforward smoking experience, appealing to both novice cooks and seasoned chefs alike, making Bradley Smokers a premium choice for indoor smoking enthusiasts.
Top Page Image Contents