S19-310PVC

Installation

Installation InstructionsInstallation Instructions

Supplies Required:

(4) 5/8" floor anchors and bolts

Pipe sealant and teflon tape

Piping to 2" IPS PVC water supply inlet on unit

Piping to 2" IPS PVC drain outlet for eye wash on unit

Adequate supply pipe supports

Minimum 4" (102mm) drain to accommodate 30 gallons per minute discharge for drench shower waste

Step 1: Assemble and Install Drench Shower

1.To secure base to floor, install four suitable anchors (supplied by installer) for 5/8" bolts in the floor (see Figure 1 on page 3).

2.Bolt the base to the floor anchors using 5/8" bolts (supplied by installer).

3.After the base is secured, assemble the remaining drench shower components as shown in Figure 1. Apply pipe sealant or tape (supplied by installer) to all male threaded pipe joints.

IMPORTANT: Some teflon sealants may cause stress cracks in the plastic showerhead leading to failure. Use teflon tape when assembling the showerhead.

4.The plastic showerhead should be assembled to the close nipple with teflon tape. The bottom edge of the showerhead should be 7' (2134 mm) from the floor.

IMPORTANT: Provide adequate supports (supplied by installer) for supply pipe using pipe hangers or other means. Do not rely on drench shower unit to support supply piping.

5.Connect the water supply piping to the 2" PVC IPS inlet on the unit (piping supplied by installer). Provide adequate supports (supplied by installer) for supply pipe using pipe hangers or other means.

6.Connect the drain piping to the 2" PVC IPS drain outlet on the unit (piping supplied by installer).

Step 2: Assemble and Install Eye/Face Wash

NOTE: See Figure 2 on page 5 for part identification.

1.While holding the elbow in the lower assembly piping, thread pipe #113-946 (Item #21) through the hole in the lower assembly piping, and connect to elbow.

2.Install the reducer on top of the elbow.

3.Center the elbow, then tighten the pipe #113-946 (Item #21) in place.

4.Install the union and pipe nipple on pipe #113-946 (Item #21).

5.Place the gasket, then the strainer, on top of the lower assembly piping.

6.Place the eyewash bowl on top of the strainer.

7.Install the yoke assembly by connecting the stainless steel pipe, at the base of the yoke assembly, to the reducer on the elbow.

8.Connect the pipe nipple to the valve piping assembly.

9.Open the water supply lines. Test for leaks and adequate water flow on the entire drench shower/eye wash unit.

4

4/27/07

Bradley Corporation • 215-1134 Rev. R; EN 06-532G

Page 4
Image 4
Bradley Smoker S19-310PVC installation instructions Installation InstructionsInstallation Instructions, Supplies Required

S19-310PVC specifications

The Bradley Smoker S19-310PVC is an exceptional addition to any outdoor cooking enthusiast's repertoire. Known for its reliability and innovative design, this smoker presents a combination of quality materials, advanced features, and user-friendly technologies that make it a top choice for both beginners and seasoned pitmasters.

One of the standout features of the S19-310PVC is its 4-rack design, which allows users to smoke a generous amount of food simultaneously. The built-in convection heating system ensures that heat is evenly distributed throughout the cooking chamber, providing consistent results every time. This model is made from high-quality materials that are both durable and capable of withstanding varying weather conditions, making it ideal for year-round outdoor use.

The Bradley Smoker employs a unique direction in smoking technology through its patented automated wood bisquette feeding system. This innovative mechanism burns wood bisquettes for a precise duration, allowing users to achieve a steady supply of smoke without the risk of bitterness that can arise from over-smoking. The 120V heating element is efficient and ensures that the smoker maintains optimal temperatures, which range from cold smoking to high-heat cooking.

Temperature control is another significant feature of the S19-310PVC. Equipped with a digital control panel, users can easily monitor and adjust the internal temperature. This accuracy allows for a variety of smoking techniques, such as cold smoking fish or hot smoking meats. Additionally, the smoker comes with a water bowl to maintain humidity levels, crucial for achieving tender and juicy results.

The design of the S19-310PVC also prioritizes user convenience. Its insulated body minimizes heat loss and reduces energy consumption. The removable racks and drip tray simplify the cleanup process after a successful smoking session. Furthermore, portability is enhanced by the integrated wheels, allowing for easy relocation to accommodate outdoor gatherings or events.

In summary, the Bradley Smoker S19-310PVC redefines outdoor smoking with its user-friendly features, innovative technologies, and durable construction. With its robust design and precise controls, this smoker is engineered for anyone who appreciates the art of smoking meats and other foods, delivering exceptional flavors and culinary experiences. Whether you’re preparing for a family barbecue or adding gourmet flavor to your culinary creations, the S19-310PVC stands out as a reliable companion for all your smoking needs.