Braun G 3000 manual Safety fuse, Before using, Assembly, Operating, Notice, Cleaning, Storage

Models: G 3000

1 34
Download 34 pages 45.68 Kb
Page 6
Image 6
Safety fuse

Safety fuse

If the motor switch is turned on, but the motor sud- denly stops or does not run, the built in safety fuse has been activated. Should this happen, turn the appliance off and wait until the motor has cooled off (approximately 15 minutes).

If the motor will not start when switching it on again, repeat the cooling off procedure (see above).

After use, turn off the appliance and unplug it.

Before using

All parts of the grinder attachment were covered with a lubricating film before leaving the factory. They must be washed before using the first time (see «Cleaning»).

Assembly

Please note the correct assembly order of parts 1- 5.

The sharp side of the blade 3 must face the disc 2.

Guide the notch B in the disc 2 over the protrusion E in the grinder head 5.

After assembling the parts 2- 4, screw the cap 1 moderately tight onto the grinder head 5.

The assembled grinder head 5 is joined to the motor unit 9with a bayonet lock. Insert the metal housing into the motor unit by holding the filling shaft of the grinder head at an angle of 45° clockwise (the Before using marking on the grinder head has to match the Assembly marking on the motor unit (A)). Turn the grinder head anti-clockwise in the direction of the upright arrow (A) until the filling shaft snaps into place in an upright position. Place the feeder tray 6 on the filling shaft.

To remove the grinder head 5press the release button eand turn the grinder head clockwise 45° as shown in picture B.

Operating

Turn on the motor before filling with meat, fish, vegetables etc. To do so, press the on switch Hso that it engages.

To turn off the appliance, press the off switch h.

In case the appliance is clogged, stop it by pressing the off switch h.

Then press the reverse button (not longer than 10 seconds).

To continue mincing, press the on switch again.

Important: Wait until the appliance has stopped completely before pressing the reverse button or the on switch.

Before processing meat, remove tendons and bones and cut it into strips. Besides meat, the machine will also process fish, vegetables, onions, soaked bread rolls, boiled potatoes, stoned plums for jam. Fill the prepared meat or vegetables into the feeder tray 6and push it down into the filling shaft with the pusher 7. Never use a fork, a spoon handle or a similar object. If meat is crushed instead of being cut properly, please check whether the meat grinder is assembled correctly

(e. g. whether you have perhaps over-looked inserting one of the parts) or clean the blade 3 and disc 2.

Notice

Before mincing frozen meat, defrost it to such a degree that you can cut it into cubes of appropriate size. These cubes can be processed with the appliance.

When processing food with high power consumption

– e. g. sunflower seeds mixed with oats at a ratio of 1:3 (approximately 800 W) – do not exceed an operating time of 10 seconds.

Before using the «Kubbe» attachment +11 / Sausage filler l, the meat has to be ground twice.

Cleaning

Wipe the motor unit 9with a damp cloth only and wipe it dry. All other parts can be washed in hot water with normal dishwashing liquids.

Storage

There is a practical cord storage j at the base of the unit (C).

Subject to change without notice.

This product conforms to the European

Directives EMC 2004/108/EC and Low

Voltage 2006/95/EC.

Please do not dispose of the product in the household waste at the end of its useful life. Disposal can take place at a Braun Service Centre or at appropriate collection points provided in your country.

6

Page 6
Image 6
Braun G 3000 manual Safety fuse, Before using, Assembly, Operating, Notice, Cleaning, Storage