Praktical Guidelines
Type of Water to be Used
This iron is designed for tap water. However, if you have hard water we recommend to use a mixture of 1/2 part tap water and 1/2 part distilled water from drug stores or grocery stores.
Important: Never use distilled water (battery water). Do not add any additives (e. g. starch) to the water.
To fi ll iron
1.Pull the plug out of the wall outlet.
2.Put the steam regulator 4 in position «•» (= steam off).
3.Open sliding shutter 2.
4.Place the iron in the upright position and fill with water slowly through the tank opening 2 to the «max.» marking L (a), using the beaker
q.
5. Close sliding shutter.
Selecting the temperature
Connect the iron to a safely located wall outlet and select the ironing temperature with the temperature selector 1 (b). As soon as the pilot light 8 goes out, the iron has reached the temperature selected. To avoid water dripping, always rest the iron upright while heating it up keep the steam regulator 4 in position «•»
(= steam off) (c).
You will usually find the following symbols in your garments:
The temperature selector 1 is marked with these symbols:
min. The iron is connected
●Synthetics (acrylic, acetate) ●● Silk/rayon/nylon/polyester/
cotton blends/wool
●●● Cotton/linen max. Linen
Select the temperature you need according to these symbols.
Spray, shot of steam, jet of steam
Before you start ironing, we recommend to press the buttons 3 or 4 times, in order to activate these functions.
Dry ironing
Set the steam regulator 4 in position «•» (= steam off) (c) for dry ironing. The water spray 7 may be used at any temperature setting to dampen the laundry. The jet of steam
6and the shot of steam 7 buttons can be activated during dry ironing, provided that the temperature selector 1 is within the continuous red area 
Steam ironing
(see «Table of features»)
Temperature selection: Set the temperature selector 1 within the red
range steam (b) and wait
until the iron has reached the selected temperature (i. e. the pilot light 8 goes off). Steam ironing is possible in the entire red range. Steam ironing at lower temperatures may cause water drops instead of steam. Should this happen, turn the steam regulator 4 to the position «•» (= steam off) (c).
Steam regulator 4: Select the quantity of steam required (c) for each garment with the steam regulator 4. You can increase the quantity by turning the steam regulator clock-
wise (wide markings) to the end of the red marking.
Caution: While ironing do not turn the steam regulator further, otherwise hot water may come out from the sole plate (see section
By turning the steam regulator
Constant steam:
Your Braun steam iron is equipped with a special tank configuration to privide constant steam even when the water level in the tank is low.
«Extra steam»* (coming from the steam vents in the sole plate): For stubborn creases and wrinkles, collars and cuffs. When ironing within the red range
area the extra steam function can
be used. You can press the button 5 (d) for 3 seconds at intervals of no less than 15 seconds.
Jet of steam* (coming from the outlets p at the slim pointed tip o): Caution: Keep children away from the jet of steam and do not hold your fingers in front of the
outlets p when activating this function.
When ironing within the red range area the jet of steam function 6 can
be used (e). To do so, press the button 6 at intervals of no less than 5 seconds. The jet of steam has been designed not only for steaming hard to reach areas like pleats, inside of pockets etc., but also for steaming hanging clothing (e. g. velvet skirts, curtains, etc.) (g). The jet of steam functions between horizontal and upright positions. Be careful not to touch sensitive textiles with the hot sole plate.
Shot of steam* (coming from the vents in the sole plate): When ironing within the red area
the shot of
steam function can be used. It gives an extra,
particularly powerful shot of steam penetrating deep into the textiles in order to straighten creases, collars and pleats. The function «shot of steam» can be used in normal ironing and also horizontally for steaming hanging clothing (e. g. velvet skirts, curtains etc.) (g). Press the shot of steam button 7 at intervals of no less than 5 seconds. When steaming be careful not to touch sensitive textiles with the hot sole plate.
*If pressed too frequently, it can drip. Should this happen, wait a few seconds before using it again.
Spray (coming from the nozzle 3):
The spray function can be used at any temperature, to dampen laundry. To do so, press the button 7 (water spray = blue).
Spray / shot of steam
and from red to blue clockwise (f).
Storage
After ironing, always pull the plug out of the wall outlet. Set the temperature selector 1 to «min.»
(b)and the steam regulator 4 to «•» (= steam off) (c).
To empty the iron hold it with the open water tank opening 2 downwards (h) and shake it 1 or 2 times. The pivoting cord 9 conveniently winds up around the cord storage k.
IMPORTANT: Store the cool steam iron in a dry place and always standing on its heel rest j. The sole plate may be damaged by remaining water if it is stored horizontally. The warranty does not cover faults or damage resulting from improper storage of the iron.
Maintenance and Cleaning
All models have an aluminium sole plate. To prevent damaging it, do not iron over buttons or zippers, etc. Clean the sole plate regularly, particularly if you use starch or other ironing aids. To remove mineral/starch residues use a vinegar and water mixture in the ratio of 1:2. Never use abrasive scouring pads, powders or liquids.
The steam vents m and jet of steam outlets p may be cleaned with a toothpick or cotton swabs and vinegar solution, if necessary.
4 | 5 |
