TROUBLESHOOTING GUIDE

25

STOVE FEEDS PELLETS, BUT WILL NOT IGNITE

Possible Causes:

Possible Remedies:

 

 

 

1.

Air damper open too far for ignition.

Push the air damper in closer to the side of the stove for startup. In

 

 

some situations it may be necessary to have the damper completely

 

 

closed for ignition to take place. After there is a flame, the damper

 

 

can then be adjusted for the desired feed setting.

 

 

 

2.

Blockage in igniter tube or inlet for igniter tube.

Find the igniter housing on the backside of the firewall. The air

 

 

intake hole is a small hole located on bottom side of the housing.

 

 

Make sure it is clear. Also, look from the front of the stove to make

 

 

sure there is not any debris around the igniter element inside of the

 

 

igniter housing.

 

 

 

3.

The burnpot is not pushed completely to the rear of the firebox.

Make sure that the air intake collar on the burnpot is touching the

 

 

rear wall of the firebox.

 

 

 

4.

Bad igniter element.

Put power directly to the igniter element. Watch the tip of the igniter

 

 

from the front of the stove. After about 2 minutes the tip should

 

 

glow. If it does not, the element is bad.

 

 

 

5.

The control board is not sending power to the igniter.

Check the voltage going to the igniter during startup. It should be a

 

 

full current. If the voltage is lower than full current, check the wiring.

 

 

If the wiring checks out good, the board is bad.

 

 

 

 

SMOKE SMELL COMING BACK INTO THE HOME

 

 

 

Possible Causes:

Possible Remedies:

 

 

 

1.

There is a leak in the vent pipe system.

 

 

 

Inspect all vent pipe connections. Make sure they are sealed with

 

 

RTV silicone that has a temperature rating on 500 degree F or

 

 

higher. Also, seal joints with UL-181-AP foil tape. Also, make sure

 

 

the square to round adapter piece on the combustion blower has

 

 

been properly sealed with the same RTV.

 

 

 

2.

The gasket on the combustion blower has gone bad.

Inspect both gaskets on the combustion blower to make sure they

 

 

 

 

are in good shape.

 

 

 

 

CONVECTION BLOWER SHUTS OFF AND COMES BACK ON

 

 

 

Possible Causes:

Possible Remedies:

 

 

 

1.

The convection blower is overheating and tripping the internal

Clean any dust off of the windings and fan blades. If cleaning the

 

temperature shutoff.

blower does not help, the blower may be bad.

 

 

 

2.

Circuit board malfunction.

Test the current going to the convection blower. If there is power

 

 

being sent to the blower when it is shut off, then the control board is

 

 

fine. If there is NOT power being sent to the blower when it shuts off

 

 

during operation, then you have a bad control board.

 

 

 

Page 25
Image 25
Breckwell P23FSA, P23I, P23FSL owner manual Stove Feeds PELLETS, but will not Ignite, Possible Causes Possible Remedies

P23FSL, P23FSA, P23I specifications

The Breckwell P23 series pellet stoves, comprising the P23FSA, P23I, and P23FSL models, are designed to provide efficient heating solutions while maintaining ease of use and aesthetic appeal. These stoves incorporate advanced technology features that set them apart in the modern heating market.

The Breckwell P23FSA model features a traditional freestanding design that blends seamlessly with any home decor. This model is equipped with a large viewing window, allowing users to enjoy the mesmerizing flames while benefiting from its high-efficiency heating capabilities. With a heating capacity of up to 2,000 square feet, it is an ideal choice for larger spaces. The P23FSA uses a digital control board that regulates the feed rate and blower settings, ensuring a consistent and reliable heat output. Additionally, it has a self-diagnostic system that alerts users to any operational issues, making maintenance straightforward.

The P23I, on the other hand, is designed for those seeking a built-in option. This insert offers the same heating capacity as its freestanding counterpart but is specifically made to fit into existing fireplaces, combining functionality with elegance. The P23I boasts a sleek design that enhances any room, while its adjustable blower ensures optimal heat distribution. The insert is also compatible with an optional wall thermostat, providing convenience and enhanced control over the heating schedule.

Lastly, the P23FSL model features a contemporary look with sleek lines and a compact design, ideal for smaller spaces without compromising on heating efficiency. This model includes a large hopper capable of holding up to 50 pounds of pellets, allowing for extended burn times and reduced refueling frequency. The P23FSL also incorporates a user-friendly control panel, providing adjustments at the touch of a button. Like the other models, it prioritizes efficiency, with a low emissions output that aligns with modern environmental standards.

All three models are built with high-quality materials to ensure durability and longevity. They utilize a pellet-burning process that significantly reduces environmental impact compared to traditional wood stoves, making them an eco-friendly heating option. With their combination of technology, efficiency, and aesthetic appeal, the Breckwell P23 series stands out as a top choice for homeowners looking for reliable and stylish heating solutions.