![](/images/new-backgrounds/1024688/2468817x1.webp)
| OM−05463 |
| 10 SERIES | ||||
|
|
|
|
|
|
| |
| c. Carefully read all tags, decals, and markings |
|
| ||||
|
|
| |||||
| on the pump assembly, and perform all duties |
|
| ||||
|
|
| |||||
| indicated. |
|
| ||||
|
|
| |||||
|
|
|
|
|
|
| |
| d. Check levels and lubricate as necessary. Re- | The pump assembly can be seriously | |||||
| damaged if the cables or chains used to lift | ||||||
| fer to LUBRICATION in the MAINTENANCE | ||||||
| and move the unit are improperly wrapped | ||||||
| AND REPAIR section of this manual and per- | ||||||
| around the pump. | ||||||
| form duties as instructed. | ||||||
|
|
| |||||
|
|
|
|
| Mounting | ||
| e. If the pump and engine have been stored for |
|
| ||||
| more than 12 months, some of the compo- | Locate the pump in an accessible place as close as | |||||
| nents or lubricants may have exceeded their | practical to the liquid being pumped. Level mount- | |||||
| maximum shelf life. These must be inspected | ing is essential for proper operation. | |||||
| or replaced to ensure maximum pump serv- | The pump may have to be supported or shimmed | |||||
| ice. | ||||||
| to provide for level operation or to eliminate vibra- | ||||||
|
|
|
|
| |||
|
|
|
|
| tion. | ||
If the maximum shelf life has been exceeded, or if |
|
| |||||
anything appears to be abnormal, contact your | To ensure sufficient lubrication and fuel supply to | ||||||
the engine, do not position the pump and engine | |||||||
mine the repair or updating policy. Do not put the | more than 15_ off horizontal for continuous opera- | ||||||
pump into service until appropriate action has | tion. The pump and engine may be positioned up | ||||||
been taken. | to 30_ off horizontal for intermittent operation | ||||||
|
|
|
|
| only; however, the engine manufacturer should be | ||
|
|
|
|
| consulted for continuous operation at angles | ||
POSITIONING PUMP | greater than 15_. | ||||||
|
|
|
|
| Clearance | ||
|
|
|
|
| When positioning the pump, allow a minimum | ||
|
|
|
|
| |||
|
|
|
|
| clearance of 18 inches (457 mm) in front of the | ||
|
|
|
|
| back cover to permit removal of the cover and easy | ||
Use lifting and moving equipment in | |||||||
access to the pump interior. | |||||||
good repair and with adequate capacity | |||||||
|
| ||||||
to prevent injuries to personnel or dam- | SUCTION AND DISCHARGE PIPING | ||||||
age to equipment. The bail is intended | |||||||
|
| ||||||
for use in lifting the pump assembly |
|
| |||||
only. Suction and discharge hoses and | Pump performance is adversely effected by in- | ||||||
piping must be removed from the pump | |||||||
creased suction lift, discharge elevation, and fric- | |||||||
before lifting. | |||||||
tion losses. See the performance curve and notes | |||||||
|
|
|
|
| |||
|
|
|
|
| on Page | ||
Lifting | lows pump to operate within the safe operation | ||||||
range. | |||||||
|
|
|
|
| |||
Use lifting equipment with a capacity of at least 650 |
|
| |||||
pounds (295 kg.). The pump weighs approxi- | Materials | ||||||
mately 130 pounds (59 kg.) not including the |
|
| |||||
weight of accessories or suction and discharge | Either pipe or hose maybe used for suction and | ||||||
piping. Customer installed equipment such as suc- | discharge lines; however, the materials must be | ||||||
tion and discharge piping must be removed before | compatible with the liquid being pumped. If hose is | ||||||
attempting to lift. | used in suction lines, it must be the | ||||||
|
|
|
|
|
|
| |
| PAGE B − 2 | INSTALLATION |