Check High Pressure Hose

The high pressure hose can develop leaks from wear, kinking, or abuse. Inspect the hose each time before using it. Check for cuts, leaks, abrasions or bulging of cover, damage or movement of couplings. If any of these conditions exist, replace the hose immediately.

WARNING

The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury and possible amputation.

•NEVER repair high pressure hose. Replace it.

•Replacement hose rating MUST exceed maximum pressure rating of unit.

Check Detergent Siphoning Tube

Examine the filter on the detergent tube and clean if clogged. The tube should fit tightly on the barbed fitting. Examine the tube for leaks or tears. Replace the filter or tube if either is damaged.

Check Spray Gun

Examine the hose connection to the spray gun and make sure it is secure. Test the trigger by pressing the red button and making sure the trigger “springs back” into place when you release it. You should not be able to press the trigger without pressing the red button. Replace spray gun immediately if it fails any of these tests.

Nozzle Maintenance

A pulsing sensation felt while squeezing the spray gun trigger may be caused by excessive pump pressure. The principal cause of excessive pump pressure is a nozzle clogged or restricted with foreign materials, such as dirt, etc. To correct the problem, immediately clean the nozzle following these instructions:

1.Shut off engine and turn off water supply.

2.ALWAYS point spray gun in a safe direction, press red button and squeeze spray gun trigger to release retained high water pressure.

WARNING

The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury and possible amputation.

Spray gun traps high water pressure, even when engine is stopped and water is disconnected, which can cause injury.

•Keep high pressure hose connected to pump and spray gun while system is pressurized.

•After each starting attempt, where engine fails to run, always point spray gun in safe direction, press red button and squeeze spray gun trigger to release high pressure.

3.Remove nozzle from end of nozzle extension.

4.Use a small paper clip to free any foreign material clogging or restricting nozzle (A).

5.Remove nozzle extension from spray gun.

6.Using a garden hose, remove additional debris by back flushing water through nozzle extension. Back flush between 30 to 60 seconds.

7.Reinstall nozzle and in-line filter into nozzle extension.

8.Reconnect nozzle extension to spray gun.

9.Make sure garden hose is connected to water inlet. Check that high pressure hose is connected to spray gun and pump. Turn on water.

10.Start engine following instructions How to Start Your Pressure Washer.

11.Test pressure washer by operating with each quick connect nozzle.

O-Ring Maintenance

Purchase an O-Ring/Maintenance Kit, model 6048, by contacting the nearest authorized service center. It is not included with the pressure washer. This kit includes replacement o-rings, rubber washer and water inlet filter. Refer to the instruction sheet provided in the kit to service your unit’s o-rings.

WARNING

The high pressure stream of water that this equipment produces can cut through skin and its underlying tissues, leading to serious injury and possible amputation.

•NEVER repair leaking connections with sealant of any kind. Replace o-ring or seal.

2550 PSI specifications

The Briggs & Stratton 2550 PSI pressure washer is a powerful cleaning tool designed to tackle a variety of outdoor tasks with ease. With a maximum cleaning power of 2550 PSI, this machine is well-equipped for efficiently removing dirt, grime, and stubborn stains from surfaces such as driveways, patios, decks, and vehicles.

One of the standout features of the Briggs & Stratton 2550 PSI pressure washer is its durable and reliable engine. Powered by a Briggs & Stratton 550 Series engine, it delivers consistent performance and dependable starts, allowing users to get to work without the frustration of engine failure. This engine is designed with an overhead valve (OHV) configuration, which increases efficiency while reducing emissions.

The pressure washer is also user-friendly, featuring a convenient push-button start system. This eliminates the need for pull cords, making it easier for anyone to get started quickly. The unit boasts an ergonomic design that includes a comfortable handle and the option for folding handles, making storage and transport simple.

In terms of functionality, the Briggs & Stratton 2550 PSI model is equipped with a 2.0-gallon per minute (GPM) water flow rate, allowing for effective cleaning without excessive water usage. The unit comes with a variety of nozzle options, providing different spray patterns to suit various tasks. The quick-connect nozzle system makes switching between nozzles easy and efficient.

Another key characteristic of this pressure washer is its rugged frame and all-terrain wheels, which ensure stability and maneuverability during operation. The wheels are designed to withstand various surfaces, allowing users to roll the machine over grass, gravel, or smooth pavement with ease.

Furthermore, the Briggs & Stratton 2550 PSI pressure washer features a built-in detergent tank that simplifies the process of applying soap while cleaning. This tank is easy to fill and ensures that users can tackle tougher cleaning jobs without the hassle of additional equipment.

With its combination of power, efficiency, and user-friendly design, the Briggs & Stratton 2550 PSI pressure washer stands out in the market as a reliable tool for homeowners and outdoor cleaning enthusiasts alike. Its blend of innovative features and practicality makes it an excellent choice for achieving professional-quality cleaning results.

Briggs & Stratton 2550 PSI manual Check High Pressure Hose, Check Detergent Siphoning Tube

Models: 2550 PSI