Change oil while engine is still warm from running, as follows:

1.Drain fuel tank by running pressure washer until fuel tank is empty.

2.Disconnect spark plug wire and keep it away from spark plug.

3.Clean area around oil fill, remove oil fill cap/dipstick. Wipe dipstick clean.

4.Tip your pressure washer to drain oil from oil fill into a suitable container making sure you tip your unit away from spark plug. When crankcase is empty, return pressure washer to upright position.

5.Slowly pour recommended oil (about 20 oz.) into oil fill opening. Pause to permit oil to settle. Fill to “Full” mark on dipstick.

6.Wipe dipstick clean each time oil level is checked. DO NOT overfill.

7.Replace and tighten dipstick.

8.Wipe up any remaining oil.

9.Reconnect spark plug wire to spark plug.

Service Air Cleaner

Your engine will not run properly and may be damaged if you run it with a dirty air cleaner.

Service the air cleaner once every 25 hours of operation or once each year, whichever comes first. Service more often if operating under dirty or dusty conditions.

To service the air cleaner, follow these steps:

1. Loosen screw (A) and tilt cover (B) down.

D

C

E

A B

2.Carefully remove cartridge (C) assembly.

3.To clean cartridge, gently tap pleated paper side on a flat surface.

4.Reinstall clean or new cartridge assembly inside cover.

5.Insert cover’s tabs (D) into slots in bottom of base (E).

6.Tilt cover up and tighten screw securely to base.

Service Spark Plug

Change the spark plug every 100 hours of operation or once each year, whichever comes first. This will help your engine to start easier and run better.

1.Clean area around spark plug.

2.Remove and inspect spark plug.

3.Check electrode gap with wire feeler gauge and set spark plug gap to 0.030 inch (0.76 mm) if necessary.

4.Replace spark plug if electrodes are pitted, burned or porcelain is cracked. Use the recommended replacement plug. See Specifications.

5.Install spark plug and tighten firmly.

Spark Arrester Service

Your engine is not factory-equipped with a spark arrester. In some areas, it is illegal to operate an engine without a spark arrester. Check local laws and regulations. A spark arrester is available from your nearest qualified service center.The spark arrester must be serviced every 50 hours to keep it functioning as designed.

If the engine has been running, the muffler will be very hot. Allow the muffler to cool before servicing spark arrester.

WARNING

Contact with muffler area can result in serious burns.

Exhaust heat/gases can ignite combustibles, structures or damage fuel tank causing a fire.

•DO NOT touch hot parts and AVOID hot exhaust gases.

•Allow equipment to cool before touching.

•Keep at least 5 feet (1.5 m) of clearance on all sides of pressure washer including overhead.

•Code of Federal Regulation (CFR) Title 36 Parks, Forests, and Public Property require equipment powered by an internal combustion engine to have a spark arrester, maintained in effective working order, complying to USDA Forest service standard 5100-1C or later revision. In the State of California a spark arrester is required under section 4442 of the California Public resources code. Other states may have similar laws.

•Remove spark arrester screen for cleaning and inspection.

•Replace if screen is damaged.

21

Page 20 Page 22
Page 21
Image 21
Briggs & Stratton 2550 PSI manual Service Air Cleaner, To service the air cleaner, follow these steps, Service Spark Plug
Page 20 Page 22

2550 PSI specifications

The Briggs & Stratton 2550 PSI pressure washer is a powerful cleaning tool designed to tackle a variety of outdoor tasks with ease. With a maximum cleaning power of 2550 PSI, this machine is well-equipped for efficiently removing dirt, grime, and stubborn stains from surfaces such as driveways, patios, decks, and vehicles.

One of the standout features of the Briggs & Stratton 2550 PSI pressure washer is its durable and reliable engine. Powered by a Briggs & Stratton 550 Series engine, it delivers consistent performance and dependable starts, allowing users to get to work without the frustration of engine failure. This engine is designed with an overhead valve (OHV) configuration, which increases efficiency while reducing emissions.

The pressure washer is also user-friendly, featuring a convenient push-button start system. This eliminates the need for pull cords, making it easier for anyone to get started quickly. The unit boasts an ergonomic design that includes a comfortable handle and the option for folding handles, making storage and transport simple.

In terms of functionality, the Briggs & Stratton 2550 PSI model is equipped with a 2.0-gallon per minute (GPM) water flow rate, allowing for effective cleaning without excessive water usage. The unit comes with a variety of nozzle options, providing different spray patterns to suit various tasks. The quick-connect nozzle system makes switching between nozzles easy and efficient.

Another key characteristic of this pressure washer is its rugged frame and all-terrain wheels, which ensure stability and maneuverability during operation. The wheels are designed to withstand various surfaces, allowing users to roll the machine over grass, gravel, or smooth pavement with ease.

Furthermore, the Briggs & Stratton 2550 PSI pressure washer features a built-in detergent tank that simplifies the process of applying soap while cleaning. This tank is easy to fill and ensures that users can tackle tougher cleaning jobs without the hassle of additional equipment.

With its combination of power, efficiency, and user-friendly design, the Briggs & Stratton 2550 PSI pressure washer stands out in the market as a reliable tool for homeowners and outdoor cleaning enthusiasts alike. Its blend of innovative features and practicality makes it an excellent choice for achieving professional-quality cleaning results.
Top Page Image Contents