Continuous Beam Using Lock Button:
Step 1: For a continuous beam, depress trigger switch and slide the lock button to the LOCKED position.
Step 2: To unlock and turn spotlight OFF, slide the lock button to the UNLOCKED position.
NOTE: To lock the Dual Xenon in the OFF position, release trigger switch, then slide the lock button to the LOCKED position.
WARNING: Always turn spotlight off when not in use.
Switching Between Single and Dual Beams:
Step 1: For single beam, slide switch on back of light to one dot, as illustrated.
Step 2: For dual beam, slide switch on back of light to two dots, as illustrated.
NOTE: The Dual Xenon will burn for approximately 40 minutes if using both beams, or approximately 85 minutes if using only one beam.
Step 1: Make sure trigger switch is not locked in the ON position.
Step 2: Plug the AC charger or DC charger/adapter into the socket located on the base of the spotlight handle as illustrated.
Step 3: For DC Charger/Adapter:
Plug the other end of the DC charger/adapter into a cigarette lighter receptacle.
For AC Charger:
Plug the other end of the AC charger into a wall outlet.
Step 4: Allow the spotlight to charge for at least 8 hours. Do not allow to charge more than 12 hours.
Note: LED indicator on base of handle turns off automatically when battery is fully charged.
Step 5: Remove spotlight from the charger before operating.
See chart for recommended charge times.Charge Times
Charge time is dependent on usage of the
product. See chart below for recommended charge time.
85
(Minutes) | 40 |
| Battery Charge |
|
| ||
USAGE |
|
| |
|
|
|
4 | 8 | 12 |
CHARGE TIME (Hours)
To Operate
Beam
Trigger
Switch
Switch
Lock
Button
Unlocked | Single |
| |
Locked | Beam |
Dual
Beam
To Charge
LED Indicator |
IMPORTANT: The EPA Certified RBRC® Battery Recycling Seal on the nickel cadmium (NiCd) battery contained in our product indicates The Brinkmann Corporation is
voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful life, when taken out of service in the United States or Canada. The RBRC® program provides a convenient alternative to placing used NiCd batteries into the trash or the municipal waste stream, which may be illegal in your area. Please call
To Replace Bulb
Glass &
Reflector
Rear
Housing
GlassRubber
Retainer Cap
To Hang/Store Dual Xenon
Tips to Avoid Damage to Your Dual Xenon Spotlight
Only use Brinkmann xenon bulb that is designed for the Dual Xenon spotlight as a replacement. Use of any other bulb may result in poor performance and may damage your spotlight.
NOTE: Handling the bulb can leave oil from your fingers on the bulb. To extend the life of the new bulb and maximize brightness, gently clean off bulb with soft cloth or tissue. Make sure the reflector does not touch or bend the bulb while replacing spotlight head.
Step 1: Disconnect spotlight from charger.
Step 2: Remove front rubber cap from barrel of spotlight.
Step 3: Pinch the wings of the glass retainer together and lift as illustrated.
Step 4: Pull glass and reflector away from rear housing.
Step 5: Pull old bulb straight out of bulb holder.
Step 6: Make certain that "legs" on new bulb are straight. Insert "legs" into the two holes in the bulb holder.
Step 7: Gently push bulb straight in until fully seated and centered.
Step 8: To reassemble, place the glass and reflector on the rear housing. Insert the glass retainer into the rear housing.
Step 9: Replace rubber cap.
WARNING: Do not touch the lamps when light is on or if it was recently on. The lamps will be hot and could cause serious burns.
The retractable hanging ring allows spotlight to hang while in use or during storage.
•Never attempt to wipe or clean the inner reflective surface of the reflector. Touching or wiping the surface will damage it permanently.
•The lens is made of tempered glass. Avoid dropping or sharp impact on spotlight to prevent damage.
•Do not allow hot lens to come in contact with water or materials subject to heat damage.
•The spotlight is weather resistant. It is not waterproof. Do not use the spotlight under water or store outdoors.
•Use only Brinkmann xenon bulb that is designed for your Dual Xenon spotlight. Use of any other bulb may result in poor performance and may damage your spotlight.
•After months of use, cigarette lighters can build up corrosion that may prevent the DC lighter plug from making good contact. It may be necessary to clean the inside of your cigarette lighter receptacle with a fine emery cloth. Before cleaning receptacle, remove the fuse to prevent it from shorting out.
2
3
