Children weighing 15-36kg (approx 4-11 years)
1 Adjusting the child seat
1a | 1b | 1c |
1d
1e
IMPORTANT – You must check | Move the headrest up or down so | To adjust the backrest, place one | Push the child seat back until it is | |
that the headrest is in the correct | that the head is positioned centrally | hand on the seat section and push | touching the car’s seat back (dia 1d). | |
position for your child before each | as in the picture (dia 1b). | firmly on the backrest until you | The cars seat backrest can be moved | |
journey. | When the headrest is in the correct | feel and hear a click (dia 1c). The | to a desired angle. | |
| backrest will now pivot freely and |
| ||
With the seat supported, squeeze | position let go of the headrest | IMPORTANT – The backrest of | ||
does not need to click into another | ||||
the headrest adjuster at the back of | adjuster and ensure it has locked | the child seat MUST always be in | ||
position. | ||||
the headrest (dia 1a). | into place. | contact with the cars seat back AND | ||
|
the base section of the child seat MUST always be in contact with the car’s seat base.
2 Installing the child seat in your car
IMPORTANT – This child seat MUST only be used with a lap and diagonal seat belt (approved to UN/ECE regulation no. 16 or equivalent standards).
If one or both sections of the child seat are not in contact with both sections of the car’s seat you MUST angle the car seat more upright (dia 1e).
IMPORTANT – Have you adjusted the headrest to the correct position for your child and ensured that the seat has an appropriate recline angle?
2a
2b
2c
2d
2e
IMPORTANT – You MUST NOT use the child seat for a child weighing more than 36kg.
Place the child seat forward facing in your car, ensuring it is pushed firmly into the car seat. Feed the diagonal section of the seat belt through the dark red upper belt guide on the OPPOSITE side to the buckle (dia 2a).
IMPORTANT – When installing the child seat, the vehicle seat must be kept in a normal upright position at all times. Reclining the vehicle seat will adversely affect the performance of the seat in a crash.
Fasten the seat belt across your child. The lap section of the seat belt should rest on the red lower belt guides on each side of the child seat (dia 2b).
IMPORTANT – The lap section of the seat belt should rest as forward and as low as possible over your child’s pelvis.
Remove as much slack as possible from the seat belt and make sure it is fitted comfortably, but tightly and is not twisted (dia 2c).
IMPORTANT – You must use the upper belt guide at all times.
IMPORTANT – Ensure that the diagonal section of the belt lays over the shoulder of the child and NOT against the neck.
Tighten the seat belt by pulling the diagonal section in the direction of the arrow
(dia 2d).
If your vehicle has an adjustable seat belt upper anchorage, adjust its height so that the seat belt passes
through the centre of the upper belt guide on the child seat and pull the seat belt to tighten 
.
IMPORTANT – The child seat must not be installed in a position where the seat belt anchorage point is level with, or forward of, the upper belt guide (dia 2e).
2f
2g
2h
Correct buckle position
IMPORTANT – Once you have installed the child seat it is important that you check the position of the seat belt buckle to ensure a secure installation.
If the seat belt buckle looks like this then the seat belt buckle position is correct (dia 2f).
If the seat belt buckle looks like this, where the buckle is being pulled around the shell into the red lower belt guide (dia 2g), try another seating position in the car.
IMPORTANT – Do not leave your child seat loose. Always fasten the seat belt across the child seat when it is not being used by your child to prevent the seat being hurled forward in the event of an accident.
If the seat belt does not lie within the red lower belt guides then the seat is not properly installed (dia 2h).
If you are in any doubt contact Customer Services on 01264 386034.
To release your child simply undo the seat belt.
3 Looking after the child seat
3a 
3b
3c
3d
Removing the cover
Unhook the elastics which hold the main cover section in place (dia 3a). The red spots show their location.
Unhook the elastic from the hook at the front of the seat (dia 3b).
Unhook the elastics from the hooks on the underside of the seat (dia 3c).
Unhook the elastics which hold the headrest cover section in place (dia 3c). The red spots show their location. The edges of the headrest cover section can now be pulled away from the seat.
