1 Removing or re-fitting your seat unit
(the seat cover must be removed before fitting the infant carrier)
1a | 1b | 1c | 1d | 1e |
B | A |
|
| A |
|
|
|
| |
|
|
|
| A |
B
B
HANDY HINT - | HANDY HINT - | Unfasten the hook and | Unclip the hooks on | Remove the seat unit |
You may find it easier | You may find it easier | loop fastenings and | both sides of the buggy | from the chassis by |
to apply the brake | to stand behind or to | press studs shown by | (dia 1d). | sliding the base tabs |
before removing or | the side of the buggy. | the red circles |
| upwards and out of the |
Remove the hood | (dia 1c). |
| grooves. | |
Please refer to the user | and bumper bar |
|
| Then slide the top tabs |
guide for your buggy for | by simultaneously |
|
| upwards and out of the |
operation of the brake. | pressing the buttons on |
|
| grooves until the seat |
Unfasten the press | the mouldings on both |
|
| unit is disengaged |
studs A on the backrest | sides of the buggy and |
|
| (dia 1e). |
and unfasten the hook | slide them upwards |
|
| To |
and loop fastenings on | until they disengage |
|
| unit reverse these |
both sides of the seat | (dia 1b). |
|
| instructions. |
unit where it overlaps |
|
|
|
|
the hood B (dia 1a). |
|
|
|
|
2 Attaching your child seat for use as a travel system
(this vehicle is intended for children from birth and up to 13kgs)
2a | 2b | 2c | 2d | 2e |
UK User Guide
HANDY HINT -
You may find it easier to apply the brake when fitting the child seat. Please refer to the user guide for your buggy.
Clip the socket onto the chassis from the inside. Align the bottom edge of the socket with the edge shown on the chassis (dia 2a). Rotate the fixing arm. Squeeze the housing and fixing arm together with one hand and snap over the hook with the other hand. Repeat this process for both sockets.
Ensure that the left hand and right hand sockets are used on the correct side of the
To fit the adaptor to the child seat squeeze the lever and insert into the space below the handle (dia 2b). Make sure it is fully fitted and release the lever to lock into place. Repeat this process for both adaptors.
Ensure that the left hand and right hand adaptors are used on the correct side of the child seat.
IMPORTANT -
The buggy seat unit must be removed before attaching your car seat.
Lower the child seat onto the buggy making sure that the adaptor on either side drops into both the sockets on each side of the buggy (dia 2c). Push down firmly. Once the seat is engaged you will hear a click.
Move the handle to the rocking position. Please refer to the user guide for the child seat.
WARNING -
Check that the child seat attachment devices are correctly engaged before use.
IMPORTANT -
Ensure your child is harnessed at all times.
To remove the child seat move the handle to the carrying position. Lift the lever on the adaptors and lift the child seat out of the sockets (dia 2d).
IMPORTANT -
It may be necessary to remove the adaptors from the child seat when installing it in your vehicle.
If the adaptors are in contact with the vehicle seat cushion, remove them.
To remove the adaptors from the child seat, pull the lever on the adaptors away from the child seat while pulling down (dia 2e). Repeat the process for both adaptors.
The child seat is compatible with the ISOFIX base (purchased separately). See www.britax.eu for further information.
Verve P-Type adaptor
Verve P-Type socket
buggy.
Only use a
1282.000 - Verve Adaptors & Sock1 1
10/1/07 09:15:40
