TEST THE ALARM
1.Make sure the Alarm is receiving AC power. Under normal operation, the Green indicator light will shine continuously. If the Green power indicator light does not light, recheck connections. If connections are correct and the Green power indicator still does not light, the unit should be replaced immediately.
2.Press and hold the test button until the alarm sounds. You will hear the signal that indicates the presence of explosive gas followed by the signal for carbon monoxide.
When testing the Alarm, have someone else check that the Alarm can be heard easily from the sleeping areas. The unit should be located where it can wake you if it alarms at night.
HOW YOUR ALARM WORKS
THE COVER OF YOUR ALARM
1. Test/Silence Button: Press and hold to activate test, or to silence the alarm.
2. POWER Light (GREEN)
3 | 2 | 3. Display |
| ||
|
|
WHAT TO DO IF EXPLOSIVE GAS IS DETECTED
If you hear the alarm horn sound one beep per second, gas has been detected. The word GAS will be displayed. Evacuate everyone from the building.
1.Leave the house immediately, opening doors and windows as you leave.
2.Do not use your telephone or appliances. Do not turn any light switches off or on. Any spark or flame could ignite the gas.
3.Call 911 and your gas company from a phone that is away from your home.
4.Do not
•If the unit alarms and you are not testing the unit, it is warning you of a potentially dangerous situation that requires your immediate attention. NEVER ignore any alarm. Ignoring the alarm may result in injury or death.
•Never disconnect the power to quiet an unwanted alarm. Disconnecting the power disables the Alarm. This will remove your protection.
Alarms have various limitations. See "General Limitations of Gas/CO Alarms" for details.
4
6
4. (Behind the Cover) Alarm Horn: 85dB audible alarm for test, alarm, and unit malfunction warning.
5. | Display Button: Press to |
1 | recall highest CO level |
recorded | |
6. | Battery Compartment |
5
USING THE SILENCE FEATURE
NEVER disconnect the power to your Alarm to silence the
•The Silence Feature is intended to temporarily silence the horn while you identify and correct the problem.
•To use the Silence Feature, press the Test/Silence button until the horn is silent.
•If the Test/Silence button is pressed while the Alarm is in the silence mode, the alarm will start sounding again.
WHEN THE GAS ALARM IS SILENCED...
IF YOUR GAS/CO ALARM SOUNDS
WHAT TO DO IF CARBON MONOXIDE IS DETECTED
Actuation of your CO Alarm indicates the presence of carbon monoxide (CO) which can kill you. In other words, when your CO Alarm sounds, you must not ignore it!
IF THE CO ALARM SOUNDS:
1.Operate the Test/Silence button.
2.Call your emergency services, fire department or 911. Write down the number of your local emergency service here:
_______________________________________________________________
3.Immediately move to fresh
4.After following steps
_______________________________________________________________
The Alarm will remain silent for approximately 2 minutes and then return to normal operation. If the gas has not cleared within the silence period, the unit will go back into alarm.
WHEN THE CO ALARM IS SILENCED...
The CO Alarm will remain silent for up to 4 minutes. While the Alarm is silenced, it will continue to monitor the air for CO. After 4 minutes, if CO levels remain potentially dangerous the horn will start sounding again.
The Silence Feature is intended to temporarily silence the Alarm horn. It will not correct a CO or gas problem.
USING THE REMOTE CONTROL TEST/SILENCE FEATURE
Using the VOLUME or CHANNEL buttons on most remote controls, you can test or silence this gas/CO Alarm from up to 12 feet (3.6 meters) away.
To Test or Silence the Alarm:
1. Make sure you have a clear path between you and the Alarm, free of any obstructions.
2. Point the remote at the front of the Alarm.
3. Press the VOLUME or CHANNEL button for at least 5 seconds.
If the Alarm does not respond to your remote control:
• You may be standing too far away.
• Your remote may not be compatible.
• You did not hold the button on your remote for at least 5 seconds.
•AC power must be present to Silence the low battery chirp.
3