Prepare the Hood, Preparando EL Extractor

PREPARE THE HOOD

1.Unpack hood and check contents. You should re- ceive:

1 - Aluminum Filter (40000 and 42000 & 42000D hoods only)

1- 3-1/4" x 10" Damper/Duct Connector (mounted inside of hood for shipping only) (40000 hood only)

1 - Ductfree Microtek® System I Filter (41000 hood only)

1 - 7” Round Damper (42000D hoods only.)

2.Remove wiring box cover. Under cover find:

1- Plastic Bag containing loose mounting hard- ware

3.Remove top or rear electrical knockout. (FIG. 2)

4.(40000 hood ONLY) Remove duct knockout. In- sert screwdriver under edge of knockout, break tabs, and peel knockout back with pliers. (FIG. 3)

5.(40000 hood ONLY) Install damper/duct connec- tor over opening made in STEP 4. Use #8B sheet metal screws provided. (FIG. 3)

(42000 hood ONLY) Install Model 87 round damper (purchase separately) over opening in top of hood. (42000D hood ONLY - Install 7” round damper (in- cluded) over opening on top of hood.

PREPARE THE INSTALLATION LOCATION

Omit STEP 1 if hood will be installed under cabinets with flush bottom.

1.(For installation on recessed bottom cabinets only) Attach a wood filler strip at each side of recessed area under cabinet. Use two 1" x 2" strips cut to length. If recess is deeper than 1" use thicker strips. Attach strips with 1-1/4" wood screws, 3" from each end of strip. See FIG. 4.

2.Measure and mark the following (FIGS. 5A & 5B): a.) Electrical wiring opening in wall or cabinet. b.) Duct opening in wall or cabinet (40000, 42000

& 42000D hoods ONLY).

WARNING

WHEN CUTTING OR DRILLING INTO WALL OR CABINET, BE CAREFUL NOT TO CUT EXISTING ELECTRICAL WIRING.

3.Use 1-1/4" bit to drill opening for electric wiring.

4.Cut out duct opening in wall or cabinet with saber saw or keyhole saw.

5.Center hood in installation opening and trace key- hole slots onto wood filler strips on cabinet bottom.

6.Screw four #10 x 7/8 wood screws into exact center of narrow end of traced keyhole slots. Allow 3/8" of screws to project, so that hood can be fitted into place later.

FIG. F

ROOF CAP 634

CASQUETE DE TECHO 634

		6" ROUND DUCT 406
3-1/4" X 10" TO 6" ROUND		DUCTO REDONDO
DUCT TRANSITION 411		DE 6 PLG. 406
ADAPTADOR DE UNA
SALIDA DE EXTRACTOR
DE
3-1/4 PLG. X 10 PLG. A UN
DUCTO	CIRCULAR
DE 6 PLG. 411

FIG. 1				WIRING		BOX			COVER
FIG. 1		CUBIERTA DE LA		CAJA	DE		CABLEADO
DUCTFREE
MICROTEK®		KEYHOLE SLOTS
SYSTEM I FILTER		KEYHOLE SLOTS
SYSTEM I FILTER		RANURAS
(41000 HOOD		RANURAS
(41000 HOOD
ONLY)
SISTEMA
DE FILTRO
DUCTFREE
MICROTEK®
MICROTEK®
(SOLO PARA
(SOLO PARA
EL MODELO 41000)
ALUMINUM
ALUMINUM
FILTER(40000,
42000&42000D
HOODS
ONLY)
FILTRODE
ALUMINIO
(SOLO				D A M P E R / D U C T
PARALOS				D A M P E R / D U C T
PARALOS				CONNECTOR				(40000
MODELOS				CONNECTOR				(40000
MODELOS				HOOD	ONLY)
40000, 42000				HOOD	ONLY)
40000, 42000	7”	ROUND	DAMPER	CONECTOR				DEL
Y 42000D)	7”	ROUND	DAMPER	CONECTOR				DEL
	(42000D HOOD ONLY)			D U C T O / R E G U L A D O R
	REGULADOR		REDONDO	(SOLO	PARA			EL
	DE 7 PULG. (SOLO PARA			MODELO			40000)
	EL	MODELO	42000D)

FIG. 2

FIG. 3

	ELECTRICAL
	KNOCKOUTS
	TAPONES	HINGE PINS
	ELECTRICOS	HINGE PINS
	ELECTRICOS	PASADORES DE
		PASADORES DE
		BISAGRA
		DUCT
		KNOCKOUTS
		TAPONES DEL
		DUCTO

	FIG. 4

PREPARANDO

EL EXTRACTOR

1.Desempaque el extractor y revise el contenido de la caja. Usted debe encontrar:

1 - Filtro de aluminio (solamente extractores modelos

40000, 42000 y 42000D)

1 - Conector de ducto/regulador de 3-1/4 plg. x 10 plg. (montado dentro del extractor para facilitar el embarque) (solamente extractores modelo 40000)

1 - Sistema de filtro Ductfree Microtek® System

1 - Regulador de 7 pulg. (campanas de 42000D solamente.)

2.Retire la cubierta de la caja de cableado. (FIG. 1) Bajo la cubierta encontrará:

1 - Bolsa de plástico que contiene las piezas necesarias para la instalación

3.Retire el tapón eléctrico trasero superior. (Fig. 2)

4.(SOLAMENTE extractores modelo 40000) Retire el tapón trasero superior. Coloque un desarmador debajo del extremo del tapón, rompa los apéndices y retire el tapón con unas pinzas. (FIG. 3)

5.(SOLAMENTE extractores modelo 40000) Instale el conector del ducto/regulador sobre la abertura hecha en el PASO 4. Utilice el tornillo de lámina negra #8B proporcionado en la bolsa de plástico. (FIG. 3)

(SOLAMENTE extractores modelo 42000) Instale el regulador Modelo 87 (comprado por separado) sobre la abertura en la parte superior del extractor.

(Campana de 4200D SOLAMENTE - Instale regulador de 7 pulg. (incluido) sobre la abertura en la tapa de la campana.

ACONDICIONE EL LUGAR DE LA INSTALACION

Si el extractor va a ser instalado bajo gabinetes con suelo nivelado, omita el PASO 1.

1.(Solamente para la instalación en los gabinetes con espacios libres) Coloque una pieza de madera en cada uno de los lados para rellenar el área libre debajo del gabinete. Utilice dos tiras de madera de 1 plg. x 2 plg. de longitud. Si el área libre tiene más de 1 plg. de profundidad, utilice piezas de madera más gruesas. Ajuste las piezas con tornillos para madera de 1-1/4 plg., a 3 plg. de los extremos. Consulte la FIG. 4.

2.Mida y marque lo siguiente (FIGS. 5A y 5B):

a.) La abertura del cableado eléctrico en la pared

o el gabinete.

b.) La abertura para el ducto en la pared o el gabinete (SOLAMENTE extractores modelos 40000, 42000 y 42000D).

ADVERTENCIA

CUANDO ESTE CORTANDO O PERFORANDO LA PARED O EL GABINETE, ASEGURESE DE NO CORTAR EL CABLEADO ELECTRICO EXISTENTE.

3.Utilice un taladro de 1-1/4 plg. para hacer la abertura para el cableado eléctrico.

4.Haga un corte en la pared o el gabinete, para la entrada del ducto, con un serrucho o una sierra de punta o de calador. (Si la pared es de concreto, haga las operaciones necesarias para la instalación.)

5.Centre el extractor en la entrada de la instalación y marque las ranuras en las piezas de madera que rellenan el espacio libre en la parte inferior del gabinete.

6.Ajuste 4 tornillos para madera #10 x 7/8 justo en el centro del extremo angosto de las ranuras marcadas. Permita que los tornillos salgan 3/8 plg. para que el extractor pueda ser colocado en su lugar.

412404 specifications

The Broan 412404 is an expertly engineered range hood that combines powerful ventilation with sleek design, making it a valuable addition to modern kitchens. This model is particularly favored for its efficient performance and aesthetic appeal.

One of the standout features of the Broan 412404 is its powerful 400 CFM blower, providing ample air circulation to effectively remove smoke, odors, and steam during cooking. This high-performance motor is designed to operate quietly, minimizing distraction while maintaining a peaceful kitchen environment. The two-speed settings allow users to customize ventilation power according to the type of cooking being done, whether it's a light sauté or a more intense frying session.

The range hood is crafted from durable stainless steel, which not only adds a contemporary finish to any kitchen but also ensures ease of cleaning and longevity. The sleek design fits seamlessly into various kitchen configurations, from traditional to modern.

Incorporating advanced technologies, the Broan 412404 features a single blower that maximizes airflow while maintaining energy efficiency. The integrated dishwasher-safe aluminum grease filters effectively trap grease and are easy to clean, promoting better hygiene in the kitchen.

Another highlight of the Broan 412404 is its recessed lighting, which provides enhanced visibility over the cooking surface. This not only improves functionality when preparing meals but also elevates the overall aesthetic of the kitchen. The energy-efficient bulbs used in the lighting will help reduce electricity consumption while providing adequate illumination.

Installation of the Broan 412404 is straightforward, making it a feasible option for both new kitchen builds and upgrades. The unit can be mounted either under a cabinet or against the wall, offering versatility based on kitchen layout and user preference.

In summary, the Broan 412404 range hood uniquely balances efficiency, design, and technology. With its robust 400 CFM blower, durable stainless steel construction, easy-to-clean filters, and stylish integrated lighting, it is an ideal choice for anyone looking to enhance their kitchen ventilation while enjoying a modern aesthetic.

Broan 412404 Prepare the Hood, Preparando EL Extractor, Acondicione EL Lugar DE LA Instalacion

Models: 412404