Broan manual

PRESTIQUE

MEDICINE CABINET

MODEL NO.	SIZE	FINISH
942224-P1	24”	White
942230-K1	30”	White
942236-K1	36”	White	For help, call
947224-Q1	24”	Oak
947230-Q1	30”	Oak	us toll free!
947236-Q1	36”	Oak
			1-800-637-1453

INSTRUCTIONS FOR WALL-MOUNT INSTALLATIONS

WARNING: Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and stan- dards, including fire-rated construction codes and standards.

Prepare cabinet.

1. Carefully remove all packing material.

Determine location.

1.The commonly accepted height of bath cabinets is 64" from the finished floor to the center of the mirror area. However, height may be adjusted to individual preference.

2.It is recommended that the cabinet be located such that the mounting screws may be screwed into wall studs to provide maximum strength.

3.Provide 120 VAC power cable through the wall material, directly behind the light box.

Mount cabinet.

1.Measure and mark four (4) clearance holes in cabinet back at wall stud locations. Use angle brackets to locate upper holes. (Fig. 1)

2.Drill ¼" dia. clearance holes through cabinet back.

3.Hold angle brackets in place over top set of holes. Mount brackets to underside of light housing with #6 x ½" screws.

4.Hold cabinet in place and make sure it is level. Screw cabinet to wall studs.

NOTE: Irregularities in wall surface may cause distortion of cabinet body when mounted. Place shims between cabinet and wall at appropriate corners.

OPTION (If wall studs are not available):4.Hold cabinet in place and make sure it is level. Mark wall through all four(4) clearance holes.

5.Set cabinet aside and drill holes in wall material for molly bolts or wall anchors (not provided).

6.Mount cabinet to wall material.

Connect electrical wiring.

WARNING: Before wiring this product, switch power off at service entrance and lock service panel to prevent power from being switched on accidentally.

1.Remove reflector from wrapper.

2.Remove protective plastic film from reflector and snap light cups onto sockets.

3.Make electrical connections between house wires and fixture wires on rear of reflector: black to black, white to white, and greenwire to a per- manent ground. (FIG. 2)

4.Attach reflector to cabinet.

Mount shelves.

1.Choose the location for the shelves from the five (5) sets of holes lo- cated on the inside of the cabinet.

2.Insert two (2) shelf tabs into holes, at desired location on one side of the cabinet. Repeat on the other side, being sure to use holes at the same height, so the shelf will be level.

3.Set shelves on pins.

Attach mirror doors.

1.Remove wrapping from mirror door. Remove hinge brackets and pres- sure plates from parts bag.

FIG. 1	WIRING	SHELF	REFLECTOR
	ACCESS
		TABS
	HOLE
ANGLE
BRACKET
			LIGHT
	SCREW		SOCKET
	#8 x 1½”	SCREW
SCREW		#6 x 3/8”
			CUP
#6 x ½”
	CLEARANCE
	HOLES
			MIRROR
			DOOR
	SHELF
	STRIKE		HINGE
	PLATE
			BRACKET
			(Pressure plate
MAGNET			beneath
			NYLON backside)
	URETHANE DISC		WASHER
FIG. 2	All electrical connections must be made in accordance
	with local code ordinances. If you are unfamiliar with

methods of installing electrical wiring, secure the services of a qualified electrician.

GREEN TOGROUNDWIREWHITE TO WHITE BLACK TO BLACK

FIG. 3	HINGE FIG. 4
	BRACKET

BACKSIDE OFPRESSURE MIRROR DOOR

PLATE

FIG. 5 FIG. 6

2.Peel paper backing from two (2) pressure plates and affix plates to backside of mirror door at upper-left and lower-left corners. (FIG. 3)

3.Slide hinge bracket(s) over top of door(s) and lightly tighten screws against pressure plate(s). (FIG. 3)

4.Place a nylon washer on the pin of the remaining hinge bracket and insert hinge bracket(s) into hole(s) in bottom of frame.

5.Lift mirror door(s) and insert top hinge bracket(s) into hole(s) in top of frame. (FIG. 4) Slide bottom of mirror door(s) into lower hinge bracket(s) (FIG. 5) and lightly tighten screws against pressure plate(s). (FIG 6)

6.Remove the 1" diameter strike plate(s) from the parts bag. Peel off the paper backing and affix plate(s) to rear of mirror door(s) at the lower corner(s) opposite the magnetic catch(es).

7.Clear urethane discs are furnished to prevent finger marks on mirror face. To mount: Remove paper backing and affix to mirror face ½” from bottom and outside edge.

A99042675C