MODEL QTXE110SFLT
Page
1b.Mount housing anywhere between trusses, joists, or
Sliding hanger bars are provided to allow for accurate posi- tioning of housing anywhere between framing. They can be used on all types of framing
| tab |
| screws (4) |
hanger | mounting |
channel (2) | |
bar (4) |
|
Attach the MOUNTING CHANNELS to the housing using the screws supplied. Make sure TABS face “up” as shown. Use the set of channel mounting holes (marked “STD”) to mount the housing flush with the bottom of the drywall. Use the other set of holes (not marked) to mount the housing flush with the top of the drywall.
hole for optional | * | screw (2) |
screw mounting (4) |
| |
|
|
2. Attach damper/ duct connector.
Snap damper / duct con- nector onto housing. Make sure connector is flush with top of housing and damper flap falls closed.
3.Install
6-inch round duc-
twork.
Connect
CONNECT WIRING
WIRING OPTION #1 - Allows fan to operate in automatic mode or manual mode (for odor control) by cycling ON/OFF switch.
MODEL 66V/66W, P66V/P66W
|
| LIGHT | BLK | BLU | LIGHT |
| |
| (ON/OFF) |
|
|
| |||
|
|
|
|
|
| ||
|
|
| COM |
|
|
|
|
NIGHT LIGHT | RED | RED | NIGHT LIGHT |
| |||
| (ON/OFF) |
|
|
| |||
| WHT |
|
|
|
| ||
|
|
|
|
|
|
| |
|
| FAN | BLK |
|
|
|
|
|
| ORG |
| BLK |
| WHT | |
(AUTO/OFF) |
| FAN | |||||
|
|
|
|
|
|
| |
|
| BLK | BRN | HUMIDITY |
| WHT |
|
120 |
|
|
| CONTROL |
|
|
|
| WHT | WHT |
|
| WHT |
| |
VAC |
|
|
|
| |||
LINE | GRD | GRD |
|
|
|
| |
IN |
|
|
|
|
| ||
SWITCH BOX | UNIT |
WIRING OPTION #2 - Fan can be turned ON, OFF, or set to operate automatically.
MODEL 77DV, 77DW, P77DV, P77DW
| bottom edge |
nail (4) | of framing |
Extend hanger bars to the width of the framing.
Hold ventilator in place with the hanger bar tabs wrapping around the bottom edge of the framing.
Nail ventilator to framing or fasten with screws (not provided) through holes near nails.
*To ensure a |
|
| RED | RED |
| FAN | BLU | BLK |
(ON/OFF/AUTO) | BLK COM |
| |
|
| WHT | |
|
|
| |
NIGHT LIGHT |
| RED | |
(ON/OFF) |
|
| |
| LIGHT | COM |
|
|
|
| |
(ON/OFF) |
|
| |
| BLK | BLK | BLK |
|
| ||
120 | WHT |
| WHT |
VAC |
| ||
LINE |
|
| |
IN | GRD |
| GRD |
SWITCH BOX
|
| BLK | FAN | WHT |
ORG |
|
|
| |
|
|
|
| |
BRN |
| HUMIDITY | WHT |
|
|
|
| ||
|
| CONTROL |
|
|
|
|
| WHT |
|
| RED | NIGHT LIGHT |
| |
|
|
| ||
| BLU | LIGHT |
| |
|
|
| ||
| WHT |
|
| |
|
| UNIT |
|
|
with screws or use a pliers to crimp mounting channels |
tightly around hanger bars. |
4. Connect electrical wiring.
Run 120 VAC house wiring to installation location. Use proper UL approved connector to secure house wiring to wiring plate. Connect wires as shown in wiring diagrams.
