15. USE AND CARE |
| 16. OPERATION |
Grease Filters
The grease filters should be cleaned frequently. Use a warm detergent solution. Grease filters are dishwasher safe. Wash more often if your cooking style generates greater
Remove filters by pushing filters towards the back of hood and rotating filters downward.
Blower Cleaning
Remove the filters in order to access the blower. Vacuum blower to clean. Do not immerse in water. Refer to blower instruction manual for more details.
Grease Rail
The grease rail should be cleaned frequently, especially if baffle filters are used.
Remove filters, then, disassemble the grease rail from the hood by removing its 3 retaining screws. See illustration below.
HD0069 |
Refer to Stainless steel cleaning in Hood Cleaning section below. Once the grease rail is clean and dry, reassemble it to the hood and reinstall filters.
Hood Cleaning
Stainless steel cleaning: How to maintain its “BRIGHT LOOK”
Do:
•Regularly wash with clean cloth or rag soaked with warm water and mild soap or liquid dish detergent.
•Always clean in the direction of original polish lines.
•Always rinse well with clear water (2 or 3 times) after cleaning. Wipe dry completely.
•You may also use a specialized household stainless steel cleaner.
Don’t:
•Do not use any steel or stainless steel wool or any other scrapers to remove stubborn dirt.
•Do not use any harsh or abrasive cleansers.
•Do not allow dirt to accumulate.
•Do not let plaster dust or any other construction residues reach the hood. During construction/renovation, cover the hood to make sure no dust sticks to stainless steel surface.
Avoid: When choosing a detergent
Always turn ON your hood before you begin cooking in order to establish an air flow in the kitchen. Let the blower run for a few minutes to clear the air after you turn off the range. This will help keep the whole kitchen cleaner and brighter.
4 |
|
| 6 |
| |
3 |
| 3 | 5 | 3 | |
1 | 1 | ||||
| 2 |
| |||
|
|
|
| ||
HC0004 |
|
|
|
| |
1. Warming lamps |
| 4. | Halogen light switches |
| |
2. Warming lamp switches |
| 5. ON/OFF Blower switch |
| ||
3. Halogen lights |
| 6. | Blower speed control |
| |
Warming lamps (Infrared)
Each warming lamp (item 1 in picture above) is controlled with is own ON/OFF switch (item 2 on picture above). Use only BR40 Size, 250 W max., Infrared bulbs (purchase separately).
!WARNING
Never place highly flammable material under warming lamps.
Cooktop Lighting (Halogen)
A double set of ON/OFF switches (item 4 on picture above) control the halogen lights (item 3 on picture above).
The front rocker controls the center light. The rear rocker controls both side lights. Select one, two, or three lights for best cooktop lighting.
Use PAR 20, 50 W halogen bulbs (purchase separately).
Blower
The blower is operated using two (2) controls.
Use the red, lighted ON/OFF switch (item 5 on picture above) to start and stop the blower. When turned on, the blower will operate at the previous setting of the speed control (item 6 on picture above).
Turn the speed control knob clockwise to decrease blower
HEAT SENTRY™
This hood is equipped with a HEAT SENTRY™ thermostat. This thermostat is a device that will turn on or speed up the blower if it senses excessive heat above the cooking surface.
1)If blower is
2)If blower is ON at a lower speed
When the temperature level drops to normal, the blower will return to its original setting.
•Any cleaners that contain bleach will attack stainless steel.
•Any products containing: chloride, fluoride, iodide, bromide will deteriorate surfaces rapidly.
•Any combustible products used for cleaning such as acetone, alcohol, ether, benzol, etc., are highly explosive and should never be used close to a range.
Enamel finish:
Clean with warm water and mild detergent only.
When discoloration occcurs, use a good enamel polish such as automotive polish. (DO NOT use rough abrasive
cleaner or porcelain cleaner.) | - 11 - |
!WARNING
The HEAT SENTRYTM can start the blower even if the hood is turned OFF. In this case, it is impossible to turn the blower OFF with blower switch. If you must stop the blower, do it from the main electrical panel.
