English
Printed in China
www.brother.comLW5497001
USER’S GUIDE
USER’S GUIDE
Thank you for choosing the
Federal Communications Commission (FCC) Declaration of Conformity (For USA Only)
Responsible Party: Brother International Corporation 100 Somerset Corporate Boulevard Bridgewater, NJ
declares that the product: Product Name:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to cor- rect the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
-Changes or modifications not expressly approved by Brother Industries, Ltd. could void the user’s authority to operate the equipment.
-The enclosed interface cable should be used in order to ensure compliance with the limits for a Class B digital device.
Getting Ready
WARNING
•Always use the specified voltage and the suggested AC adapter
•Unplug the power cord immediately and stop using the
•Do not use the AC adapter in places of high humidity such as bathrooms.
•Do not overload the power cord.
•Do not place heavy objects on, or damage the power cord or plug. Do not forcibly bend or pull the power cord. When disconnecting the power cord from the power outlet, al- ways hold the plug.
•To prevent fire or electric shock, make sure that the plug is fully inserted to the power outlet. Do not use an outlet that is loose.
•Do not get the machine/AC adapter/power plug wet, such as by handling them with wet hands or spilling beverages on to them.
•Do not disassemble or modify
•Do not use metallic articles, such as tweezers or a metallic pen, when exchanging the batteries.
•Do not throw into fire or heat up the battery.
•Disconnect the AC adapter, remove batteries and stop using immediately if you notice any abnormal odor, heat, discoloration, deformation or anything unusual while in use, or in storage.
CAUTION
•To avoid injuries, do not touch the blade of the cutter unit or any metal parts near the print head.
•Do not apply excessive pressure to the cutter lever.
•Remove the batteries and disconnect the AC adapter if you do not intend to use
•Do not use old and new batteries together or mix alkaline batteries with other type batteries, or set the positive and negative end in the wrong position. Otherwise, the batter- ies may leak or be damaged.
•To prevent damage or breakage, do not drop or hit
•Use only the USB cable included with the
•Depending on the location, material, and environmental conditions, the label may unpeel or become irremovable, the color of the label may change or be transferred to other objects. Before applying the label, check the environmental condition and the material.
•Do not use the
•Use only Brother TZ tapes with this machine. Do not use tapes that do not have the mark.
•Do not clean
•Do not touch the print head with your fingers anytime to prevent from a burn. Use a soft wipe (e.g. a cotton swab) when cleaning the print head.
•Do not put any foreign objects into the tape exit slot or AC adapter connector, etc.
•Do not place the
•Do not try to print labels using an empty tape cassette in the
•Do not pull the tape being fed from the
LED lamp |
|
Power/feed |
|
button |
|
Tape cutter |
|
button | Print head |
Tape exit slot | Tape cutter |
| |
AC adapter(optional) |
|
connecter |
|
USB port |
|
Mode selector |
|
switch |
|
The
Open the cassette | Insert a tape |
|
|
|
|
|
| Close the cassette |
cover. | cassette. |
|
|
|
|
|
| cover. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Verify that the | Insert a TZ tape cassette as shown | • Make sure that the end of the tape feeds under the tape |
turned off. Open the cassette cover | in the above illustration. | guides. |
as shown by the arrow in the above |
| • If the ink ribbon is loose, use your finger to wind the toothed |
illustration while pressing the part |
| wheel in the direction of the arrow on the cassette. |
marked "<<". |
| • Use only Brother TZ tapes with the |
|
| • For initial use of the tape, install the tape, press and hold the |
|
| power/feed button to feed the tape. Then, push in the tape cut- |
|
| ter lever to cut the tape. |
Insert six new AAA alkaline batteries (LR03), making sure that their poles point in the correct directions. Always replace all six batteries at the same time using brand new ones.
When using the optional AC adapter
When the
Connect the | Turn on the |
USB cable. | The LED lamp will light up. |
The following screens may differ depending on the Operating System on your PC.
Click
Click Open folder to
It will take longer than usual to start
For details on using
Do not turn off the power or remove the labeler while using
Windows Vista®
When connecting the device for the first time, perform the scan and then select the Always do this for software and games check box on the dialog box displayed when the scan completes.
view files.
*Microsoft Windows and Windows Vista are registered trademarks of Microsoft Corporation in the United States and other countries.
*The name of other software or products used in this document are trademarks or registered trademarks of the respective companies that developed them.
Exit
To disconnect the labeler, click the icon in the computer’s task bar ( , , or ).
Click Safely remove USB Mass Storage Device. When The device can be safely removed is displayed, turn off the
Starting | If you would like to use the more advanced software that is available for your |
you are able to download | |
| ware will give you greater label making functionality. |
| Do not connect the |
| tor 5.0 installation. |
| Download and install the | Start | Use |
Move the mode selector | driver and | ||
er’s website. Connect the | |||
switch on the back of the | to your PC when requested during this |
|
|
installation. |
|
| |
|
|
| |
position before connect- | For more information about install- | • | If you have trouble using |
ing the USB cable. | ing the software, visit http://solu- | cut icon on the desktop | the software, refer to the |
| tions.brother.com/ | help information available | |
|
| • Click | in |
|
| under All Programs on |
|
|
| the Start menu. |
|