Brunton 81-100726 operating instructions Warranty, Limits of Liability

		OPERATING INSTRUCTIONS	Using the stove
	- Before using the Brunton Bantam stove, please read and follow all the steps		1. Unfold the stove legs and place the stove on a flat surface.
	below carefully.
BANTAMTM
		Filling the fuel bottle
	1.	Pour the fuel up to the fill line on the bottle. Do not overfill.
Instructions for 81-100726	2.	Insert pump and turn clockwise to tighten.

fill line

3. Before pumping pressure into the fuel

bottle, ensure that the control valve for the

2. After connecting the flexible hose to

stove unit is set to the OFF position. Pump

the handle on the pump set to pressurize

the pump, ensure that the fuel bottle is

the fuel bottle (20 strokes).

20-30 times

placed on a flat surface.

NOTE: Less fuel in the bottle needs more

pumping strokes to pressurize the bottle.

Use outdoors only and do not allow children to reach

WARNING

Please read, understand and follow all instructions and warnings before using this

WARNING

Using the stove on uneven surface is very dangerous and may cause a fire hazard

product. The proper fuel bottle for this product is included.

To avoid the possibility of serious injury, use only a Brunton pump and bottle.

and serious injury.

When the fuel bottle has been connected to the pump be sure that the valve knob is set

Use only White Gasoline, other fuel could clog the nozzle and may cause a fire hazard.

to the OFF position.

Keep away from children.

When the stove is in use, keep fuel bottle as far away as possible.

www.brunton.com

PARTS REPLACEMENT AND MAINTENANCE

Stove parts

Poor performance & nozzle clogging

Checking & replacing seals and 0-rings

- Colgging inside the nozzle or generator tube may disturb the fuel and create poor stove

head

performance.

- Remove clogging inside the nozzle hole with a nozzle pin.

Dried or torn parts need to be replaced. Check the color and size and any printed

leg pin

leg A

oil plate

- If clogging persists inside of the nozzle or generator tube, a more thorough cleaning

markings and contact your nearest Brunton stock list or retailer for replacements.

is required.

o-ring

(Oil seals, Oil, Nozzle, Tool kit)

leg B

A) How to clean with nozzle pin

leg B

1. Turn off the stove valve and wait until the stove has completely

pump knob

cooled down.

pipe bolt

2. Remove the Jet by disassembling and removing the generator tube

Pump parts

assembly from the stove with the tool kit.

pipe bushing

ring

3. Clean the jet with the nozzle pin

guide spring

guide spring

wave washer

4. Re-Assemble the stove and check for any fuel leaks.

guide

venturi

guide

nozzle

pump knob

nozzle

filter

packing washer

nozzle

hose cap

heating pipe

heating pipe

body nut

guide washer

nozzle connect bolt

nozzle

bolt

packing holder

connect nut

o-rings

connect

hose washer

nozzle body

- If cleaning the Jet does not improve the stove efficiency, clean the generator tube as well.

packing rubber

B) How to clean the generator tube

connect bushing

setting bushing

pipe bolt

hose

valve

1. Begin by removing the generator tube assembly from the stove with

spindle

the tool kit.

head assembly

pipe bushing

connect

setting bolt

valve connect bolt

2. Pull the wire out brush clean of any debris and replace

3 . Re-Assemble the stove and check for any fuel leaks

housing cap

housing

o-rings knob

nylon hose

pipe

filter

o-rings

air bushing body

WARNING

o-ring

air bolt

air bushing

After disassembling and assembling, be sure to check for leakage with soapy water.

air spring

Preheating the stove	2.	After fuel has been primed to the stove, ignite the fuel through the ignition port with a		Extinguishing the stove
- Before using the stove with white gas, it is necessary to pre-heat the fuel. This is called	lighter or a match to preheat the generator pipe.			1. To extinguish the stove, turn the valve knob to the OFF position and flip the bottle over.
priming the stove.	3. After pre-heating (1-2minutes) slowly open the valve to allow fuel to flow through the			NOTE: The stove will continue to burn for a short time until all of the fuel in the generator tube
	generator unit. The flame may appear yellow for the first minute of operation but should			and fuel hose is consumed.	Flip
1. Turn the valve knob counter clockwise to the (ON) position and wait 1-2 seconds until the	settle to a crisp blue flame that is the normal cooking flame. If an excessively high yellow
	flame is evident, turn off the stove and repeat the preheating process.
jet emits a small amount of fuel onto the priming pad then close the valve by rotating the knob
	4.	Never allow fuel to overflow from the stove base, as leaking fuel will ignite and may
counter clockwise to the (OFF) Position. If fuel does not flow, the fuel bottle is low on
	cause a fire hazard and serious injury.
gas and the bottle may need preasurizing or more fuel.
	5.	If the flame decreases in intensity, further pressurization of the fuel bottle is required.
				Small flame remains for 2-3
				minutes consuming all the fuel in
				the hose.
				2. After the fire extinguishes, the stove will remain hot, wait until the stove cools down.
1-2 seconds				3. Separate the stove from pump.
				4. Fuel bottle and pump can be transported as a connected assembly. When separating the
				pump from fuel bottle, turn the pump slowly so that the pressure retainedy			inside the fuel
				bottle can release gradually.
		Manual ignition
			Turn slowly counter-	Hissing
			clockwise after preheating
WARNING
Before igniting the stove, ensure that the valve knob is turned to				Inner pressure exclusion		Separation
		Preheating	Working
the clockwise (OFF) position.

Never place your head or body above the stove when lighting it.

	WARRANTY
Brunton warrants this product to be free of defects in workmanship and materials for the
lifetime of the original owner, and is nontransferable. If you have any problems with your
Brunton stove, the stove should be returned to the dealer or sent to Brunton, 2255
Brunton Court, Riverton, WY 82501 U.S.A. Please contact Brunton at the number below
to obtain RA#. Clean food and soot from stove before shipping. Shipping cost to Brunton
is the responsibility of the purchaser. Return postage will be paid by Brunton. Please
return this warranty card to Brunton as a proof of purchase. This warranty does not cover
damage caused by accident, misuse, abuse, or tampering. A nominal charge will be		VISIT OUR WEBSITE AT www.brunton.com
assessed to repair such damage.
	2255 Brunton Court, Riverton, WY USA 82501
www.brunton.com	PH: 307.857.4700

	LIMITS OF LIABILITY		Warranty card must be filled out completely and returned within 30 days with proof of purchase for warranty to be valid.
			BRUNTON
Brunton assumes no responsibility for any inconvenience, loss, or injury, direct or			ATTN: WARRANTY DEPT.
			2255 BRUNTON COURT
consequential damage arising from possession or use of the goods. This warranty gives			RIVERTON, WYOMING 82501
you specific legal rights which may vary from state to state. Check with your local state			307.857.4700
about your rights.			BRUNTON WARRANTY REGISTRATION
			NAME_______________________________________________________
			ADDRESS___________________________________________________
			CITY_________________________ST/PROV_______ZIP__________
			PHONE _______________________EMAIL_______________________
			MODEL#__________________DATE PURCHASED____________
	WARNING
			PURCHASED FROM_______________________________________
	Only use in well ventilated areas.	Keep well away from children.	CITY_________________________ST/PROV_______ZIP__________
			PRICE PAID $___________________	1006
	Do not leave unattended while in use.	Do not operate near flammable materials.