Bryant manual Dimensions, 313AAV/JAV

313AAV/JAV

DIMENSIONS
			5.1
			[130.5]
				2 1/16
				[51.6]
					1.7
					[43.5]
				C
				Ø7/8
				[22.2]
			FRONT OF CASING	ACCESSORY (2)
				1 15/16
				[49.2]	2 5/16
	5 15/16			3 7/16
					[59]
	[150.7]	AIR FLOW		[86.8]
	5 1/2			5 7/8
	[140.3]
				[148.5]
					TOP OF CASING
8 7/16		Ø7/8			Ø7/8
		[22.2]			[22.2]
[213.5]					JUNCTION BOX
		ACCESSORY
9 7/8					LOCATION
[250.7]
		Ø1/2		Ø1 3/4
27 3/4		[12.7]
		THERMOSTAT WIRE ENTRY		[44.5]
[704.7]
				GAS ENTRY
33 1/4
[843.9]
		Ø7/8
		[22.2]
		ACCESSORY
		21.6	6.1
		[549.5]	[155.7]
		BOTTOM INLET
		28.39
		[721.2]
		29
		[736.9]

AIR FLOW

A

B

TOP OF CASING

D	3/4
BOTTOM RETURN	[19.1]
WIDTH

			FRONT OF CASING
			8 5/8
		6 13/16	[219]
	5 7/8	[172.3]
	[148.5]	5 5/8	AIR FLOW
	5 7/16	[143.3]
			19
	[138.5]	1 15/16
			[481.7]
		[49.2]	OUTLET
	4 13/16		Ø1/2
	[122.2]		[12.7]	7 13/16	9 11/16
9 9/16			THERMOSTAT WIRE ENTRY	[197.8]
			Ø1 3/4		[245.4]	11 7/16
[243.3]
			[44.5]			[290.7]
			GAS ENTRY
27 3/4		Ø7/8
		[22.2]
[704.7]
	J.BOX PROVISION
29 9/16		Ø7/8
[750.7]		[22.2]
	ACCESSORY
			Ø7/8	14 7/8
				[337.3]
			[22.2]	(BOTH SIDES)
			ACCESSORY
KNOCK OUTS FOR					1 1/4
VENTING(5
			22 1/16	1	[31.8]
PLACES)
			[560]	[25.4]
			SIDE INLET
			(BOTH SIDES)

A10271

1.Two additional 7/8-in. (22 mm) dia. knockouts are located in the top plate.

2.Minimum return-air openings at furnace, based on metal duct. If flex duct is used, see flex duct manufacturer’s recommendations for equivalent diameters.

3.Minimum return-air opening at furnace.

a.For 800 CFM-16-in. (406 mm) round or 14-1/2 x 12-in. (368 x 305 mm) rectangle.

b.For 1200 CFM-20-in. (508 mm) round or 14-1/2 x 19-1/3 in. (368 x 491 mm)rectangle.

c.For 1600 CFM-22-in. (559 mm) round or 14-1/2 x 22-1/16-in. (368 x 560 mm) rectangle.

d.For airflow requirements above 1800 CFM, see Air Delivery table in Product Data literature for specific use of single side inlets. The use of both side inlets, a combination of 1 side and the bottom, or the bottom of single side inlets. The use of both side inlets, a combination of one side and the bottom, or the bottom only will ensure adequate return air openings for airflow requirements above 1800 CFM.

		A		B		C		D	VENT	ACCESSORY-
FURNACE SIZE	CABINET		OUTLET WIDTH		TOP & BOTTOM		BOTTOM INLET		CONNECTION	MEDIA CABINET
		WIDTH		IN (MM)	FLUE COLLAR			WIDTH	SIZE	SIZE
		IN (MM)				IN (MM)		IN (MM)		IN (MM)
024045	14---	3/16 (360)	12---	9/16 (319)	9---	5/16 (237)	12---	11/16 (322)	4	16 (406)
048070	17	--- 1/2 (445)	15	--- 7/8 (403)	11---	9/16 (294)	16	--- 1/8 (410)	4	16 (406)
048090		21 (533)	19	--- 3/8 (492)	13---	5/16 (338)	19	--- 1/2 (495)	4	20 (508)
060110		21 (533)	19	--- 3/8 (492)	13---	5/16 (338)	19	--- 1/2 (495)	4	20 (508)
060135	24	--- 1/2 (622)	22	--- 7/8 (581)	15---	1/16 (383)		23 (584)	4*	24 (610)

*135 size furnaces require a 5 or 6---in. (127 or 152 mm) vent. Use a vent adapter between furnace and vent stack. See Installation Instructions for complete installation requirements.

8